02-16-2012
Help Me: How to set ARP stale time interval on linux platform for Ipv6 interface
Hi,
Can any one please help me increase the arp stale time of an ipv6 interface on linux platform ?
I have tried increasing the variable gc_stale_time but that doesnt work.
Thanks
10 More Discussions You Might Find Interesting
1. Solaris
What is the time_wait interval for Solaris 8/9??? and is it configurable???
For example sometimes a clients pc will freeze up dropping the connection, closing the port. The problem is on our side our system still thinks their logged in (until it realizes it dropped on the otherside and drops on... (1 Reply)
Discussion started by: eloquent99
1 Replies
2. UNIX for Dummies Questions & Answers
I have a script I want to run in the background, and I have looked it up but I am not exactly sure how to do. First of all to run it in the background do you have to put something in the script or is it just a command when you go to run it. I found this solution to it but once again I am not to... (2 Replies)
Discussion started by: mauler123
2 Replies
3. UNIX for Dummies Questions & Answers
Hi All,
I am new to this forum....
Can neone please help me how to copy files between two time intervals i.e. I need to copy files from 6.30 to 9.30 on 5th June 09.
Any help is appreciated. (2 Replies)
Discussion started by: Pratik4891
2 Replies
4. AIX
Hi,
I am trying to list all the interface present in the given system.
Here is sample program.
i.e. cat 1.c
#include <sys/types.h>
#include <sys/socket.h>
#include <sys/ioctl.h>
#include <sys/dlpi.h>
#include <net/if.h>
/*#include <sys/sockio.h>*/
#include <unistd.h>
#include... (3 Replies)
Discussion started by: jgobbur
3 Replies
5. Solaris
Hi, anyone has had experience in a static setting an IPv6 interface?, I'm trying accordance with the admin guide (ipv6 network configuration tasks), configure one interface in the server, actually i can do ping to my default gateway and access the Internet in IPv6, the specific point is however,... (3 Replies)
Discussion started by: pabloluja
3 Replies
6. Shell Programming and Scripting
Folks,
I need to send a .log file to my email for every one hour from a server that too only in a particular time period. Is awk mandate here? or can we do it in shell scripting only? Please help me in sorting this out.
Cheers,
Arun (3 Replies)
Discussion started by: ArunJanga
3 Replies
7. IP Networking
Hello all,
I am trying to receive (tcp/udp/sctp) traffic from all IPs and, eventually, all ports of an IPv6 address block using as few sockets as possible short of implementing my own network stack.
One possible solution was to associate an IP block to an interface then bind to that... (6 Replies)
Discussion started by: redwil
6 Replies
8. UNIX for Dummies Questions & Answers
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
9. Solaris
Hello dears
how to assign IPv4 and IPv6 addresses with same interface on solaris 10 (1 Reply)
Discussion started by: ttashman
1 Replies
10. Solaris
Hi,
I am trying to set mtu value for ipv6 interfaces. I know how to set it for ipv4 interfaces
ifconfig net1 mtu 1240
Do I need to add any iptype for the above command ?
Note:
OS:Solaris 10
TIA (3 Replies)
Discussion started by: Sumanthsv
3 Replies
EDSC(4) BSD Kernel Interfaces Manual EDSC(4)
NAME
edsc -- Ethernet discard network interface
SYNOPSIS
device edsc
DESCRIPTION
The edsc interface is a software discard mechanism which may be used for performance analysis and software testing. It imitates an Ethernet
device, which allows for its use in conjunction with such drivers as if_bridge(4) and vlan(4).
As with other network interfaces, an edsc interface must have network addresses assigned for each address family with which it is to be used.
These addresses may be set or changed with the SIOCSIFADDR ioctl(2) or ifconfig(8) utility.
Each edsc interface is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or using the
cloned_interfaces variable in rc.conf(5).
SEE ALSO
ioctl(2), arp(4), if_bridge(4), inet(4), intro(4), vlan(4), rc.conf(5), arp(8), ifconfig(8)
HISTORY
The edsc device was derived from the disc(4) device and first appeared in FreeBSD 6.3. This manpage was adapted from disc(4).
CAVEATS
Since outgoing packets are just discarded by edsc, ARP requests stay unreplied. Consequently, an IP packet cannot be sent via edsc until a
static arp(4) entry is created for its next hop using arp(8).
Initially an edsc interface has a zero link level address. It can be changed with ifconfig(8) lladdr if needed.
BSD
March 25, 2007 BSD