Hardware RAID not recognize the new disk [Sun T6320]
We have hardware RAID configured on Sun-Blade-T6320 and one of the disk got failed. Hence we replaced the failed disk. But the hot swapped disk not recognized by RAID. Kindly help on fixing this issue.
We have 2 LDOM configured on this server and this server running on single disk.
Last edited by DukeNuke2; 02-14-2012 at 10:00 AM..
I don't understood why on SPARC-Platforms have not present RAID-Controller ? Sorry for my bad english, but it's crazy always setup software RAID !!! I whanna Hardware RAID and when i can find solution ? (7 Replies)
Hi everyone
I've just purchased a Sun T5120 server with 2 internal disks. I've configured hardware RAID (mirror) and as a result the device tree in Solaris only contains 1 hard drive.
My question is, how would I know when one of the drives become faulty?
Thanks (2 Replies)
HI guys.
Bit of a noob so bear with me.
I have 2 new disks I want to add to my StorEdge 3310 but am getting lost in the steps. We have another 3310 (JBOD) that I was able to plug the disks into and they instantly showed up. Did a few minor commands after (drvconfig, devfsadm etc..) and I was... (4 Replies)
Can you mix DIMMs in a T6320 (sparc) blade? I have read/heard that the DIMMs in a memory bay must be identical but can you have different size DIMMs installed in the blade?
For instance, can you have 1 4GB DIMM in bay 0, 2 2GB DIMMs in bay 1, 4 1 GB DIMMs in bay 2 and 2 2GB DIMMs in bay 3 for a... (0 Replies)
Hi All
I have a Sun T2000 server. Couple of years ago I had configured and mirrored the boot drive with an other drive using hardware RAID 1 using raidctl command.
Following is the hardware RAID output.
root@oracledatabaseserver / $ raidctl
RAID Volume RAID RAID Disk... (0 Replies)
Hardware:
HP P2000
HP DL380 G7 with Solaris
Software:
Solaris 10 05/08
I had made a Hardware raid on P2000 and install solaris on G7,
The raid card controller is working fine.
How can I make the raid works on OS??
"raidclt" is getting nothing :wall::wall:
Thanks (11 Replies)
Hi all
I've just received my T3-1. It has 8 disks and I would like to configure RAID1 on the disks. The Sun documentation states that you can either use the OpenBoot PROMP utility called Fcode or you can use software via the Solaris OS.
The documentation doesn't make it clear if:
1. The... (6 Replies)
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
LEARN ABOUT DEBIAN
mkqdisk
mkqdisk(8) Quorum Disk Management mkqdisk(8)NAME
mkqdisk - Cluster Quorum Disk Utility
WARNING
Use of this command can cause the cluster to malfunction.
SYNOPSIS
mkqdisk [-?|-h] | [-L] | [-f label] [-c device -l label] [-d [-d ...]]
DESCRIPTION
The mkqdisk command is used to create a new quorum disk or display existing quorum disks accessible from a given cluster node.
OPTIONS -c device -l label
Initialize a new cluster quorum disk. This will destroy all data on the given device. If a cluster is currently using that device
as a quorum disk, the entire cluster will malfunction. Do not run this on an active cluster when qdiskd is running. Only one
device on the SAN should ever have the given label; using multiple different devices is currently not supported (it is expected a
RAID array is used for quorum disk redundancy). The label can be any textual string up to 127 characters - and is therefore enough
space to hold a UUID created with uuidgen(1).
-f label
Find the cluster quorum disk with the given label and display information about it.
-L Display information on all accessible cluster quorum disks.
-d Increase debugging level. Specify multiple times for more information. Currently, specifying more than twice has no effect.
SEE ALSO qdisk(5), qdiskd(8), uuidgen(1)
July 2006 mkqdisk(8)