Hardware RAID not recognize the new disk [Sun T6320]
We have hardware RAID configured on Sun-Blade-T6320 and one of the disk got failed. Hence we replaced the failed disk. But the hot swapped disk not recognized by RAID. Kindly help on fixing this issue.
We have 2 LDOM configured on this server and this server running on single disk.
Last edited by DukeNuke2; 02-14-2012 at 10:00 AM..
I don't understood why on SPARC-Platforms have not present RAID-Controller ? Sorry for my bad english, but it's crazy always setup software RAID !!! I whanna Hardware RAID and when i can find solution ? (7 Replies)
Hi everyone
I've just purchased a Sun T5120 server with 2 internal disks. I've configured hardware RAID (mirror) and as a result the device tree in Solaris only contains 1 hard drive.
My question is, how would I know when one of the drives become faulty?
Thanks (2 Replies)
HI guys.
Bit of a noob so bear with me.
I have 2 new disks I want to add to my StorEdge 3310 but am getting lost in the steps. We have another 3310 (JBOD) that I was able to plug the disks into and they instantly showed up. Did a few minor commands after (drvconfig, devfsadm etc..) and I was... (4 Replies)
Can you mix DIMMs in a T6320 (sparc) blade? I have read/heard that the DIMMs in a memory bay must be identical but can you have different size DIMMs installed in the blade?
For instance, can you have 1 4GB DIMM in bay 0, 2 2GB DIMMs in bay 1, 4 1 GB DIMMs in bay 2 and 2 2GB DIMMs in bay 3 for a... (0 Replies)
Hi All
I have a Sun T2000 server. Couple of years ago I had configured and mirrored the boot drive with an other drive using hardware RAID 1 using raidctl command.
Following is the hardware RAID output.
root@oracledatabaseserver / $ raidctl
RAID Volume RAID RAID Disk... (0 Replies)
Hardware:
HP P2000
HP DL380 G7 with Solaris
Software:
Solaris 10 05/08
I had made a Hardware raid on P2000 and install solaris on G7,
The raid card controller is working fine.
How can I make the raid works on OS??
"raidclt" is getting nothing :wall::wall:
Thanks (11 Replies)
Hi all
I've just received my T3-1. It has 8 disks and I would like to configure RAID1 on the disks. The Sun documentation states that you can either use the OpenBoot PROMP utility called Fcode or you can use software via the Solaris OS.
The documentation doesn't make it clear if:
1. The... (6 Replies)
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
LEARN ABOUT DEBIAN
raidfile.conf
RAIDFILE.CONF(5) Box Backup RAIDFILE.CONF(5)NAME
raidfile.conf - Userland RAID for Box Backup
SYNOPSIS
/etc/box/raidfile.conf
DESCRIPTION
The raidfile.conf is usually generated by raidfile-config(8) but may be manually edited if the store locations move or if more than one
disc set is required.
discX
Specifies a set of discs.
SetNumber
The set number of the RAID disc, referenced by each account.
BlockSize
The block size of the file system (usually 2048). Under BSD with FFS, set this to your file system's fragment size (most likely an
8th of the block size).
Dir0
The first directory in the RAID array.
Dir1
The second directory in the RAID array. If you do not wish to use the built-in RAID functionality, this field should be set to the
same as Dir0. You should not use the built-in RAID if you have a hardware RAID solution or if you're using another type of software
RAID (like md on Linux).
Dir2
The third directory in the RAID array. The same notes that apply to Dir2 also apply to Dir3.
FILES
/etc/box/raidfile.conf
SEE ALSO raidfile-config(8), bbstored.conf(5)AUTHORS
Ben Summers
Per Thomsen
James O'Gorman
Box Backup 0.11 10/28/2011 RAIDFILE.CONF(5)