Hi All,
Can anyone help me..
I want to know the command to check the overall CPU usage of the server.
Note:
I don't want the CPU usge of each and every process.
I just want to know thw aggregate CPU utilization of the server. (2 Replies)
how can I find cpu usage memory usage swap usage and
I want to know CPU usage above X% and contiue Y times and memory usage above X % and contiue Y times
my final destination is monitor process
logical volume usage above X % and number of Logical voluage above
can I not to... (3 Replies)
We are using linux OS. I want to extract the CPU usage on specific time for last one week. The information i need is,
date, CPU, %user , %nice , %system , %iowait, %idle
Is there anyway, i can pull these info... Any help is highly appreciated. (4 Replies)
Hi Guys,
I need to write a script capable of identifying when a high cpu utilitzation process. It sounds simple but we are on a AIX 5.3 environment with Virtual CPU's (VP's) and logical CPU's. Please any ideas or tips would be highly appreciated. Thanks.
Harby. (6 Replies)
Hi All,
Anyone has script to monitor AIX total processes memory and cpu usage that contribute to the total memory and CPU utilize so far ?
The purpose of this is to analyze process memory trend.
Thanks.
Best Regards,
ckwan (2 Replies)
hi, i am using solaris server. I want to find the total CPU usage on a server. Top command will give that result, but here that command is not working. So anyone can help me to find the total CPU usage. (2 Replies)
Hi all
I was wondering if its possible to write a script to keep CPU usage at 90%-95%? for a single cpu linux server?
I have a perl script I run on servers with multple cpu's and all I do is max all but one cpu to get into the 90'% utilised area. I now need a script that raises the CPU to... (4 Replies)
Hi Fellas,
Not sure how I can dig in even further but we notice that one of our DB servers is showing high Sys% CPU usage even though when I execute the following command :
I can see that postgres is the only one using the CPU. So if anyone can advise me what would be the best way to... (3 Replies)
Discussion started by: arizah
3 Replies
LEARN ABOUT X11R4
chcpu
CHCPU(8) System Administration CHCPU(8)NAME
chcpu - configure CPUs
SYNOPSIS
chcpu -c|-d|-e|-g cpu-list
chcpu -p mode
chcpu -r|-h|-V
DESCRIPTION
chcpu can modify the state of CPUs. It can enable or disable CPUs, scan for new CPUs, change the CPU dispatching mode of the underlying
hypervisor, and request CPUs from the hypervisor (configure) or return CPUs to the hypervisor (deconfigure).
Some options have a cpu-list argument. Use this argument to specify a comma-separated list of CPUs. The list can contain individual CPU
addresses or ranges of addresses. For example, 0,5,7,9-11 makes the command applicable to the CPUs with the addresses 0, 5, 7, 9, 10, and
11.
OPTIONS -c, --configure cpu-list
Configure the specified CPUs. Configuring a CPU means that the hypervisor takes a CPU from the CPU pool and assigns it to the vir-
tual hardware on which your kernel runs.
-d, --disable cpu-list
Disable the specified CPUs. Disabling a CPU means that the kernel sets it offline.
-e, --enable cpu-list
Enable the specified CPUs. Enabling a CPU means that the kernel sets it online. A CPU must be configured, see -c, before it can be
enabled.
-g, --deconfigure cpu-list
Deconfigure the specified CPUs. Deconfiguring a CPU means that the hypervisor removes the CPU from the virtual hardware on which
the Linux instance runs and returns it to the CPU pool. A CPU must be offline, see -d, before it can be deconfigured.
-p, --dispatch mode
Set the CPU dispatching mode (polarization). This option has an effect only if your hardware architecture and hypervisor support
CPU polarization. Available modes are:
horizontal The workload is spread across all available CPUs.
vertical The workload is concentrated on few CPUs.
-r, --rescan
Trigger a rescan of CPUs. After a rescan, the Linux kernel recognizes the new CPUs. Use this option on systems that do not auto-
matically detect newly attached CPUs.
-V, --version
Display version information and exit.
-h, --help
Display help text and exit.
RETURN CODES
chcpu has the following return codes:
0 success
1 failure
64 partial success
AUTHOR
Heiko Carstens <heiko.carstens@de.ibm.com>
COPYRIGHT
Copyright IBM Corp. 2011
SEE ALSO lscpu(1)AVAILABILITY
The chcpu command is part of the util-linux package and is available from Linux Kernel Archive <https://www.kernel.org/pub/linux/utils
/util-linux/>.
util-linux July 2014 CHCPU(8)