02-10-2012
Dear bartus11,
thank you very very much for your PERFECT answer
I have all the commands you've mentioned and I'll study their man-pages.
Before I've posted my questions, I've run
man st, but somehow I didn't understand anything
One more question: What if my system had a ZFS filesystem, may I also use the
ufsdump/ufsrestore commands or should I rather go for
tar command in that case?
BEST regards,
pc
Last edited by pseudocoder; 02-10-2012 at 04:28 PM..
Reason: iCODE tags :-)
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I'm running SCO OS 505 on a Compaq proliant 1600, and my tape drive will just not work. It was working properly and whent to Sh?ts when I tried to get the cd rom working. I have uninstalled any configured tape drive and rebooted and then configured a tape drive and rebooted still nothing. I'm... (4 Replies)
Discussion started by: kikkin
4 Replies
2. Filesystems, Disks and Memory
I'm researching a tape drive + backup software to work across my unix/linux network. Was thinking about a dds4 tape drive (sony's) on my solaris ultra2, with some kind of software that would work across the network to back up my other 2 solaris boxes, plus my 2 linux boxes. What do others use... (3 Replies)
Discussion started by: kymberm
3 Replies
3. Filesystems, Disks and Memory
Hi all, please help I am stuck.
I have installed a external unipack scsi tape drive. The tape drive is Exabyte Eliant 820. All I did was connected scsi cable and power it on. When issued "probe-scsi-all" command, the tape is correctly identified. However, when issued "dmesg | more" command, the... (4 Replies)
Discussion started by: dennis
4 Replies
4. Solaris
hi-
I just installed a quad gigaswift ethernet scsi card to my sunblade 150. I checked with the docs, and got all of the required drivers on the box. Now, I'm trying to mount an external scsi tape drive with no luck. I set the scsi address on the external drive to 0. Here's what I'm coming... (9 Replies)
Discussion started by: ECBROWN
9 Replies
5. SCO
Hello,
I'm having some issues with installing SCSI tape drive on SCO 5.0.6
hardware config shows the following adapters
%adapter 0xE800-0xE8FF 10 - type=alad ha=0 bus=0 id=7 fts=sto
%adapter 0x0170-0x0177 15 - type=IDE ctlr=secondary dvr=wd
%adapter - 3 - ... (3 Replies)
Discussion started by: ananth_ak
3 Replies
6. Solaris
Can I do this live? Or, do I need to do a probe-scsi-all after doing a stop/A? (10 Replies)
Discussion started by: jgordon
10 Replies
7. UNIX for Dummies Questions & Answers
Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies
8. AIX
I have 2 servers in my office which are p570 and p550. Both run under AIX 5300-07. And I only have 1 x SCSI Ultrium LTO3 Tape Drive. For syncronization purposes, I always backup p570 server's database and restore into p550 server.
And due to the frequent process of syncronization, I require to... (1 Reply)
Discussion started by: kwliew999
1 Replies
9. Hardware
I've had a scsi hard drive, scsi tape drive, and cd rom working off an adaptec 29160 controller. Everything worked great until a few days ago. I begin getting tar format errors (running sco 5.0.6) on the tape drive and occasionally the entire system would hang up while trying to access data on... (0 Replies)
Discussion started by: powwm
0 Replies
10. AIX
i connect an ibm ultrium lto 5 (sas) to an 8204-e8a (v6.1 TL5 SP 1)
then i do an cfgmgr and get message about missing filesets
devices.pciex.1410ca03
devices.pciex.pciexclass.00107
devices.pciex.00107200
devices.pciex.pciex100.72.3
and a few others
i try to find the filesets on the two OS... (1 Reply)
Discussion started by: AIXBlueCat
1 Replies