I have written a script using awk to split a file based on some identifier and renaming the file based on two values from specific length. ts a fixed width file.
When I am trying to fetch the values
i am getting spaces in a and b values .
I have to form a file like a_b.txt but the file is forming as "a _ b .txt"
Please help guys.
Last edited by Franklin52; 02-09-2012 at 05:29 AM..
Reason: Please use code tags for code and data samples, thank you
Hi,
I have a CSV file with footer information as below. The third value is the number of records in the file. Sometimes it contains both leading and trailing white spaces which i want to trim using awk.
C,FOOTER , 00000642
C,FOOTER , 00000707
C, FOOTER,... (2 Replies)
Hi All, I need your help.I want to know how to delete the spaces in a variable in unix scripting.Please give solution to this probelm...
thanks ! :confused: (14 Replies)
Hi Friends,
Can any one help with this issue:
How to trim spaces for each line at the end,
Like I have a file in this format.
EMP1 SMITH 46373 5 STREET HOWARD 74636
EMP2 JONES 5454 { these are spaces ........}
EMP3 SMITH 46373 5 STREET HOWARD 74636
EMP4 JON 2554 { these are... (1 Reply)
Hi,
I'm new to shell programming. Need some help in the following requirement:
I have a file origFile.txt with values:
origFile.txt
.00~ 145416.02~ xyz~ ram kishor
.35~ 765.76~ anh reid~ kishna kerry
Now each row in the file has value for 4 columns with "~" as... (7 Replies)
Hi,
I have a file origFile.txt with values:
origFile.txt
.00~ 145416.02~ xyz~ ram kishor ~? ~ ~783.9
.35~ 765.76~ anh reid~ kelly woodburg ~nancy ~ ~?
Now each row in the file has value for 7 columns with "~" as delimiter.
The requirement was
i)I need to erase the blank spaces between... (2 Replies)
All,
i am comparing the output of one command to a numberic
if ]
but my problem is the output of follwoing is but but has some leading columns. I don't have any problme in LINUX and HP-UX. But only in AIX i am getting the leading spaces. I have developed my script on LINUX but when... (4 Replies)
Hi,
I am using the below code to get a numeric value from oracle to unix variable:
BD_RC_CNT=`sqlplus -s ${WMD_DM_CONNECT} <<EOF
set heading off
set pagesize 0
Select count(*)
from wmd_bad_data
where proc_id = ${PROC_ID}
and file_id = ${FILE_ID}
and file_dt =... (7 Replies)
I have a file like this.
hari,corporationbank,2234356,syndicate
ravi,indian bank,4567900000000,indianbank,accese
raju,statebank of hyderabad,565866666666666,pause
Here each record has different record length and there are blank spaces... (8 Replies)
Discussion started by: kshari8888
8 Replies
LEARN ABOUT DEBIAN
get-iab
GET-IAB(1) General Commands Manual GET-IAB(1)NAME
get-iab - Fetch the arp-scan IAB file from the IEEE website
SYNOPSIS
get-iab [options]
DESCRIPTION
get-iab fetches the Ethernet IAB file from the IEEE website, and saves it in the format used by arp-scan.
The IAB file contains all of the IABs (Individual Address Blocks) that have been registered with IEEE. Each IAB entry in the file speci-
fies the first 36-bits of the 48-bit Ethernet hardware address, leaving the remaining 12-bits for use by the registering organisation. For
example the IAB entry "0050C2003", registered to Microsoft, applies to any Ethernet hardware address from 00:50:c2:00:30:00 to
00:50:c2:00:3f:ff inclusive. Each IAB assignment represents a total of 2^12 (4,096) Ethernet addresses.
Major Ethernet hardware vendors typically use an OUI registration rather than an IAB registration. See get-oui(1) for details.
This script can be used to update the arp-scan IAB file from the latest data on the IEEE website. It is relatively rare to see Ethernet
addresses from IAB registrations, so the IAB file is not as important as the OUI file.
The IAB data is fetched from the URL http://standards.ieee.org/regauth/oui/iab.txt and the output file is saved to the file ieee-iab.txt in
the current directory. The URL to fetch the data from can be changed with the -u option, and the output file name can be changed with the
-f option.
The ieee-iab.txt file that is produced by this script is used by arp-scan to determine the Ethernet card vendor from its hardware address.
The directory that arp-scan will look for the ieee-iab.txt file depends on the options used when it was built. If it was built using the
default options, then it will look in /usr/local/share/arp-scan.
OPTIONS -h Display a brief usage message and exit.
-f <fn>
Write the output to the specified file instead of the default ieee-iab.txt.
-u <URL>
Use the specified URL to fetch the raw IAB data from instead of the default http://standards.ieee.org/regauth/oui/iab.txt
-v Display verbose progress messages.
FILES
ieee-iab.txt
The default output file.
EXAMPLES
$ get-iab -v
Renaming ieee-iab.txt to ieee-iab.txt.bak
Fetching IAB data from http://standards.ieee.org/regauth/oui/iab.txt
Fetched 230786 bytes
Opening output file ieee-iab.txt
1535 IAB entries written to file ieee-iab.txt
NOTES
get-iab is implemented in Perl, so you need to have the Perl interpreter installed on your system to use it.
get-iab uses the LWP::Simple Perl module to fetch the data from the IEEE website. You must have this module installed on your system for it
to work. This module is available on most distributions, often called libwww-perl. It is also available in source form from CPAN.
You can use a proxy server by defining the http_proxy environment variable.
AUTHOR
Roy Hills <Roy.Hills@nta-monitor.com>
SEE ALSO arp-scan(1)get-oui(1)arp-fingerprint(1)
http://www.nta-monitor.com/wiki/ The arp-scan wiki page.
March 30, 2007 GET-IAB(1)