Sponsored Content
Operating Systems Solaris Solaris 10 Changing of nic link_speed Post 302596955 by jlliagre on Wednesday 8th of February 2012 07:15:24 PM
Old 02-08-2012
As its name suggests, the e1000g is a gigabit interface.

However, you do not set that speed. The standards require it to be negotiated between both parties. It might be a configuration issue like auto-negotiation disabled on either side.
 

9 More Discussions You Might Find Interesting

1. IP Networking

not able to add nic in solaris 8

Hi Folks, I've just installed solaris 8, but i cannot add my network card. i've reboot the box, got into the configmode, and try'd to add a network card. but it doesn't work. I can't add a ip address to the card, an error occurs. Who do i add it. Kind Regards (3 Replies)
Discussion started by: noripsni
3 Replies

2. UNIX for Advanced & Expert Users

Changing MAC address of a NIC

All, I have a need to software change the MAC address of a NIC in a Sparc Ultra 10 - I believe there is a command that allows to do this at boot up? Is it a missing (to me) part of ifconfig ? If so, what is the syntax? All replies gratefully received ! Thanks Andrew (3 Replies)
Discussion started by: wretch
3 Replies

3. Solaris

NIC drivers+solaris 10

Installed solaris 10 and now i want to connect to internet,to make work this i need to NIC drivers can some body tell me is it possible to get drivers and how to install. I am dying to get rid of this problem..please help me (1 Reply)
Discussion started by: srinivas2828
1 Replies

4. Red Hat

changing ethernet NIC names?

I have an RHEL 5 server with 2 Broadcom on-board NICs and 2 quad-port Intel NICs. After I installed the OS, the Intel NICs became eth0-7, and the onboards are eth8 and eth9. I really need the onboard NICs to be eth0 and eth1 (I have plans to later remove the quad-ports and replace them with 10gE... (1 Reply)
Discussion started by: GKnight
1 Replies

5. Linux

changing speed of NIC Card in linux

Hi, I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0 and my requirement is 100mbps full duplex. Regards, Manoj (3 Replies)
Discussion started by: manoj.solaris
3 Replies

6. Solaris

Solaris, identifying NIC hw issues

Can someone point out which steps are to be done to get information if NIC on Solaris is malfunctioned and/or not working properly. Since my Solaris knowledge is very modest, i would apreciate any help. OS is Solaris 10 x86 Regards. Peasant. ---------- Post updated at 11:57 AM... (0 Replies)
Discussion started by: Peasant
0 Replies

7. Solaris

NIC detection problem in solaris

Hi, Hardware: Mother board: Asus P5G4IC-M LX On board NIC: PCIe Gigabite LAN Kernel Ver.: SunOS 5.10 Generic_141445-09 I've NIC detection problem in Solaris 10. When I was trying to install in x86 machine, it was not asking for any Network settings which means it couldn't find NIC. But... (7 Replies)
Discussion started by: vicky86ind
7 Replies

8. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies

9. UNIX for Advanced & Expert Users

Changing single path NIC to a teamed connection in same subnet

Dear all, I have a remote CentOS7 server that has two network cards. Each card has four ports and port one of card one was defined with the IP address assigned to the server. So far, so good and it's been working for over a year. We have now got cables sorted out so there are four paths... (4 Replies)
Discussion started by: rbatte1
4 Replies
sg_get_network_iface_stats(3)				     Library Functions Manual				     sg_get_network_iface_stats(3)

NAME
sg_get_network_iface_stats - get network interface statistics SYNOPSIS
#include <statgrab.h> sg_network_iface_stats *sg_get_network_iface_stats(int *entries); DESCRIPTION
The sg_get_network_iface_stats function takes a pointer to an int, entries, which is filled with the number of network interfaces the machine has. This is needed to know how many sg_network_iface_stats structures have been returned. A pointer is returned to the first sg_network_iface_stats. sg_get_network_iface_stats returns statistics about the network interfaces in the machine. Specifically, it returns the speed of the inter- face, the duplex state, and whether it is currently up. RETURN VALUES
The sg_get_network_iface_stats returns a pointer to a structure of type sg_network_iface_stats. typedef enum{ SG_IFACE_DUPLEX_FULL, SG_IFACE_DUPLEX_HALF, SG_IFACE_DUPLEX_UNKNOWN }sg_iface_duplex; Note: The SG_IFACE_DUPLEX_UNKNOWN value could mean that duplex hasn't been negotiated yet. typedef struct{ char *interface_name; int speed; sg_iface_duplex duplex; int up; }sg_network_iface_stats; interface_name The name known to the operating system. (eg. on linux it might be eth0) speed The speed of the interface, in megabits/sec. duplex The duplex state the interface is in. See sg_iface_duplex for permitted values. up Whether the interface is up. SEE ALSO
statgrab(3) WEBSITE
http://www.i-scream.org/libstatgrab/ i-scream $Date: 2005/07/13 09:31:53 $ sg_get_network_iface_stats(3)
All times are GMT -4. The time now is 02:11 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy