01-23-2012
You may have to hit F12 on boot or similar on your computer to tell it to boot from a device other than your CDROM or primary hard drive. You might be able to alter the boot order more persistently in your CMOS settings, how to get there is system and model dependent.
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi,
I have an SGI workstation running on Irix 6.5. A few days ago the system started giving messages that the root directory is full. Even before I could find out how to clean up the root directory, the system crashed and does not boot anymore. Can anyone help me on how I can get the system to... (1 Reply)
Discussion started by: gnanavvk
1 Replies
2. Solaris
Hi all ,
I have an E2900 SPARC IV that has Solaris 10 installed , I am trying to replace solaris 10 with soalris 9/04 , But the installation is giving me an error:
Cannot assemble drivers for root /ssm@0,0/pci@18,700000/pci@4/ide@2/cdrom@0,0:b
Cannot mount root on... (3 Replies)
Discussion started by: ppass
3 Replies
3. UNIX for Dummies Questions & Answers
during installation i created four partitions mainly
/ 5GB
/home 1GB
/boot 100MB
swap 2GB
now since i didnt make the /usr partition all of the packages were being installed in the / partition ..now all the space in the / partition is filled ...i ran du -h... (3 Replies)
Discussion started by: tarunicon
3 Replies
4. Solaris
Hi community,
Does anyone can tell me the difference between "boot cdrom" and "boot cdrom - install" ?
Thank you very much:D (3 Replies)
Discussion started by: Sunb3
3 Replies
5. UNIX for Advanced & Expert Users
Hi All,
I have successfully backup & restore (using tar) one of my Debian Lenny Servers.
On the restore server (standby machine), everytime i have to erase the disk & extract the tar backup.
I want to extract the tar on the running restore server on a directory for e.g /systembackup-01,... (11 Replies)
Discussion started by: coolatt
11 Replies
6. HP-UX
Hello,
I have a very old hp rp2450 running 11i2 that I had to power off. When turning it back on it hangs with the following message. Would booting into SUM get me any further? I've never used SUM, so I'm asking before I go down that rabbit hole.
Thanks for the help.
#
## extra content... (1 Reply)
Discussion started by: calabaria
1 Replies
7. UNIX for Dummies Questions & Answers
Came home the other day to a Napp-it Gui that would not load.
Login would appear but when i attempted I would get the following
Set default permissions and reading disk and pool parameter, please wait..
in case of problems, try a reboot after Power-Off or check disk and pool status at CLI.... (1 Reply)
Discussion started by: fastedd27
1 Replies
8. UNIX for Beginners Questions & Answers
Good day,
Anybody, know how to clean/free up the Cluster_boot partition in TRU64
Thank you in advance
Miaka (0 Replies)
Discussion started by: miaka1012
0 Replies
LEARN ABOUT X11R4
installboot
installboot(1M) installboot(1M)
NAME
installboot - install bootblocks in a disk partition
SYNOPSIS
installboot bootblk raw-disk-device
The boot(1M) program, ufsboot, is loaded from disk by the bootblock program which resides in the boot area of a disk partition.
The ufs boot objects are platform-dependent, and reside in the /usr/platform/platform-name/lib/fs/ufs directory. The platform name can be
found using the -i option of uname(1).
The installboot utility is a SPARC only program. It is not supported on the architecture. users should use installgrub(1M) instead.
bootblk The name of the bootblock code.
raw-disk-device The name of the disk device onto which the bootblock code is to be installed; it must be a character device which is read-
able and writable. Naming conventions for a SCSI or IPI drive are c?t?d?s? and c?d?s? for an IDE drive.
Example 1: Installing UFS Boot Block
To install a ufs boot block on slice 0 of target 0 on controller 1 of the platform where the command is being run, use:
example# installboot /usr/platform/`uname -i`/lib/fs/ufs/bootblk
/dev/rdsk/c1t0d0s0
/usr/platform/platform-name/lib/fs/ufs
directory where ufs boot objects reside.
/platform/platform-name/ufsboot
second level program to boot from a disk or CD
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
od(1), uname(1), boot(1M), init(1M), kadb(1M), kernel(1M), monitor(1M), reboot(1M), rpc.bootparamd(1M), init.d(4), attributes(5)
WARNINGS
The installboot utility fails if the bootblk or openfirmware files do not exist or if the raw disk device is not a character device.
11 Apr 2005 installboot(1M)