Hmmm. Does the liveusb use udev? You could configure udev to prevent it from creating certain kinds of device nodes. Without those, clonezilla would be unable to use the disk.
For example there's a default rule on my system for USB devices:
You could flip that a bit:
Make sure that rule runs really early, naming the new rule file lower than everything else. 00-customrules perhaps.
I think that would create any non-USB disk or CDROM devices inside /dev/skipme/sd... and cause it to not create the ordinary /dev/sd... device nodes. If clonezilla uses them to detect disks, it won't find non-USB devices.
Last edited by Corona688; 01-20-2012 at 03:02 PM..
Will some one tell me what this means.
"warning: ida 0 <slot 6> : command timed out on dev 1/42 blk 4824290 logical unit=0 blocks=5512102, size 2, cmd=0x20."
I'm running SCO 505 on a proliant 1600r.
Thnank you in advance. (3 Replies)
I am using an Acer Aspire 4720Z with two partitions C and D. Windows is installed on C and I decided to install Red Hat Linux 9 in partition D. The two partitions are in NTFS file system. During my installation of the the Linux, a prompt was displayed on screen with the message: "No hard drives... (2 Replies)
Any recommend manufacturers for an internal SCSI tape drive in my FreeBSD 7.0 home server? Besides RAID-1, I'm not backing-up, but man, are they expensive! What makes a tape drive so darn pricy? There is no way I can afford a new drive so I'll start looking on eBay and craigslist to see if there... (3 Replies)
Version: solaris 10 x86
I just got a western digital external harddrive formated with fat 32. this drive came with some setup files which is meant for windows or mac.
I want to reformat and partition this drive into two ( for solaris and windows) such that the setup files will still be there... (2 Replies)
Folks;
I just added 2 physical new hard drives to my SUSE server. My server is already running SUSE 10.3 version.
Is there a command i can use to add the new space or even see if the system can sees them? (3 Replies)
Hello, I need to write a program which sets server's ip address, router, network mask. Program also should set if it is an internal or external ip. Maybe someone can help me ? Any information from u is very useful :b:
I stopped at .. :(
#!/bin/sh
A=`hostname -i`
echo "server ip address is $A"... (4 Replies)
I have a T2000 Sun-Fire server. I have 2 sets of drives in a raid 1. Lets call them Set A and Set B. I had Set A installed and working. I needed a new install so I so build up Set B. After some time I wanted to put Set A back in the server. Now the system will not boot off of Set A. I tried to boot... (7 Replies)
Hello everyone. I have a question which I may know the answer to, I'm just looking for a confirmation. When it comes to the MBR of a hard drive, i've read in multiple sources that it's always located in the first sector of the hard drive. Is the MBR there from the factory? When I buy a new blank... (3 Replies)
Hi,
I have two SCSI Hard Drives in a Sun Solaris 8 server as shown below. I would like to access Disk1 and look at its contents, directory structure and files. How do I change my default directory from Disk 0 to Disk 1 and vice versa?
Thank you. (5 Replies)
Ok so i thought i was smart but i can tell I need some help. I am playing around with understanding lvm and adding disks to a linux box. I added a disk and then ran what i thought were commands to add this disk to the box but I think I messed up and would like some help. My question is did i... (5 Replies)
Discussion started by: cptkirkh
5 Replies
LEARN ABOUT MOJAVE
lsusb
lsusb(8) Linux USB Utilities lsusb(8)NAME
lsusb - list USB devices
SYNOPSIS
lsusb [ options ]
DESCRIPTION
lsusb is a utility for displaying information about USB buses in the system and the devices connected to them.
OPTIONS -v, --verbose
Tells lsusb to be verbose and display detailed information about the devices shown. This includes configuration descriptors for the
device's current speed. Class descriptors will be shown, when available, for USB device classes including hub, audio, HID, communi-
cations, and chipcard.
-s [[bus]:][devnum]
Show only devices in specified bus and/or devnum. Both ID's are given in decimal and may be omitted.
-d [vendor]:[product]
Show only devices with the specified vendor and product ID. Both ID's are given in hexadecimal.
-D device
Do not scan the /dev/bus/usb directory, instead display only information about the device whose device file is given. The device
file should be something like /dev/bus/usb/001/001. This option displays detailed information like the v option; you must be root
to do this.
-t Tells lsusb to dump the physical USB device hierarchy as a tree. This overrides the v option.
-V, --version
Print version information on standard output, then exit successfully.
RETURN VALUE
If the specified device is not found, a non-zero exit code is returned.
FILES
/var/lib/usbutils/usb.ids
A list of all known USB ID's (vendors, products, classes, subclasses and protocols).
SEE ALSO lspci(8), usbview(8).
AUTHOR
Thomas Sailer, <sailer@ife.ee.ethz.ch>.
usbutils-007 6 May 2009 lsusb(8)