01-18-2012
Thanks amrit....
That was a thoughtful way of teaching me....
It's working now.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi, dear all, I am rather new to Unix and have this problem where I cant seem to ping from 1 host to another. The scenerio is as follows: -
1 QNX host->Eth->1 SCO host
the SCO host is configured with it's IP
the QNX host is configured with another IP
both in the same domain, ie, 172.20.3.XX... (3 Replies)
Discussion started by: gavon
3 Replies
2. UNIX for Dummies Questions & Answers
I have Sco openserver 5.0. It had a 125. ip. I changed it to a 192. ip. was unable to ping the 192. I was told to change it in the
etc/tcp
etc/hosts
files which i did. still unable to ping.
i am getting a message unable to route to host.
I also have an error in my etc/tcp file on line... (1 Reply)
Discussion started by: pdoug76
1 Replies
3. UNIX for Dummies Questions & Answers
DEar all
i am receiving this error on start and then unable to ping
(dlpid): unable to open network adapter driver (/dev/mdi/e3h0)
what to do ? (2 Replies)
Discussion started by: sak900354
2 Replies
4. IP Networking
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies
5. Solaris
hi,
I setup a Solaris machine in my server room and my client cannot access it. Can anyone advise?
Test that i have done:
-My client pc cannot ping the server.
-My solaris server cannot ping client
-My solaris server can ping it's gateway
-Another NT machine 1 (10.179.30.26) in the server... (2 Replies)
Discussion started by: skiturn
2 Replies
6. IP Networking
hi,
I setup a Solaris machine in my server room and my client cannot access it. Can anyone advise?
Test that i have done:
-My client pc cannot ping the server.
-My solaris server cannot ping client
-My solaris server can ping it's gateway
-Another NT machine 1 (10.179.30.26) in the... (8 Replies)
Discussion started by: skiturn
8 Replies
7. Solaris
Hi ALL,
I Have installed NEW v240 server through hyper terminal, After installation i unable to ping the server from out side server... i can see no entry in resolve.conf file.. but the server has DNS.. willl that issue.. please guide me ping the server from outside within the same network
bk (1 Reply)
Discussion started by: suresh_krish
1 Replies
8. UNIX for Dummies Questions & Answers
Hi all,
I have a VM on Solaris 10 setup on a windows vista host machine.
1) Vista host i configure
VMnet 1: 10.1.1.10
Mask : 255.255.255.0
Subnet : 10.1.1.2
DNS : 10.1.1.100
2) Solaris on VM
Network device is on Custom(VMNET1)
IP : 10.1.1.4
Mask : 255.255.255.0
... (8 Replies)
Discussion started by: JuveZzZ
8 Replies
9. Windows & DOS: Issues & Discussions
Hello All,
I have searched and searched, but I am not finding any answers. Any help would be very welcome.
I have a home LAN centered around an Untangle gateway (up to date).
I have a Windows 7 PC and a Snow Leopard Mac
I also have two virtualized instances of windows (xp and 7) running... (1 Reply)
Discussion started by: toadtilley
1 Replies
10. AIX
Hi all,
I have gone through many posts related to this issue,but my issue wasn't resolved hence creating new thread.
I am unable to ping localhost.
ping localhost tries to ping localhost which is defined in DNS.
My /etc/hosts has entry for localhost as
127.0.0.1 loopback localhost.
... (8 Replies)
Discussion started by: chpsam
8 Replies
LEARN ABOUT OPENDARWIN
pwd
PWD(1) BSD General Commands Manual PWD(1)
NAME
pwd -- return working directory name
SYNOPSIS
pwd [-LP]
DESCRIPTION
The pwd utility writes the absolute pathname of the current working directory to the standard output.
Some shells may provide a builtin pwd command which is similar or identical to this utility. Consult the builtin(1) manual page.
The options are as follows:
-L Display the logical current working directory.
-P Display the physical current working directory (all symbolic links resolved).
If no options are specified, the -P option is assumed.
ENVIRONMENT
Environment variables used by pwd:
PWD Logical current working directory.
DIAGNOSTICS
The pwd utility exits 0 on success, and >0 if an error occurs.
STANDARDS
The pwd utility conforms to IEEE Std 1003.1-2001 (``POSIX.1'').
SEE ALSO
builtin(1), cd(1), csh(1), sh(1), getcwd(3)
BUGS
In csh(1) the command dirs is always faster because it is built into that shell. However, it can give a different answer in the rare case
that the current directory or a containing directory was moved after the shell descended into it.
The -L option does not work unless the PWD environment variable is exported by the shell.
BSD
February 4, 2002 BSD