01-18-2012
Thanks amrit....
That was a thoughtful way of teaching me....
It's working now.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi, dear all, I am rather new to Unix and have this problem where I cant seem to ping from 1 host to another. The scenerio is as follows: -
1 QNX host->Eth->1 SCO host
the SCO host is configured with it's IP
the QNX host is configured with another IP
both in the same domain, ie, 172.20.3.XX... (3 Replies)
Discussion started by: gavon
3 Replies
2. UNIX for Dummies Questions & Answers
I have Sco openserver 5.0. It had a 125. ip. I changed it to a 192. ip. was unable to ping the 192. I was told to change it in the
etc/tcp
etc/hosts
files which i did. still unable to ping.
i am getting a message unable to route to host.
I also have an error in my etc/tcp file on line... (1 Reply)
Discussion started by: pdoug76
1 Replies
3. UNIX for Dummies Questions & Answers
DEar all
i am receiving this error on start and then unable to ping
(dlpid): unable to open network adapter driver (/dev/mdi/e3h0)
what to do ? (2 Replies)
Discussion started by: sak900354
2 Replies
4. IP Networking
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies
5. Solaris
hi,
I setup a Solaris machine in my server room and my client cannot access it. Can anyone advise?
Test that i have done:
-My client pc cannot ping the server.
-My solaris server cannot ping client
-My solaris server can ping it's gateway
-Another NT machine 1 (10.179.30.26) in the server... (2 Replies)
Discussion started by: skiturn
2 Replies
6. IP Networking
hi,
I setup a Solaris machine in my server room and my client cannot access it. Can anyone advise?
Test that i have done:
-My client pc cannot ping the server.
-My solaris server cannot ping client
-My solaris server can ping it's gateway
-Another NT machine 1 (10.179.30.26) in the... (8 Replies)
Discussion started by: skiturn
8 Replies
7. Solaris
Hi ALL,
I Have installed NEW v240 server through hyper terminal, After installation i unable to ping the server from out side server... i can see no entry in resolve.conf file.. but the server has DNS.. willl that issue.. please guide me ping the server from outside within the same network
bk (1 Reply)
Discussion started by: suresh_krish
1 Replies
8. UNIX for Dummies Questions & Answers
Hi all,
I have a VM on Solaris 10 setup on a windows vista host machine.
1) Vista host i configure
VMnet 1: 10.1.1.10
Mask : 255.255.255.0
Subnet : 10.1.1.2
DNS : 10.1.1.100
2) Solaris on VM
Network device is on Custom(VMNET1)
IP : 10.1.1.4
Mask : 255.255.255.0
... (8 Replies)
Discussion started by: JuveZzZ
8 Replies
9. Windows & DOS: Issues & Discussions
Hello All,
I have searched and searched, but I am not finding any answers. Any help would be very welcome.
I have a home LAN centered around an Untangle gateway (up to date).
I have a Windows 7 PC and a Snow Leopard Mac
I also have two virtualized instances of windows (xp and 7) running... (1 Reply)
Discussion started by: toadtilley
1 Replies
10. AIX
Hi all,
I have gone through many posts related to this issue,but my issue wasn't resolved hence creating new thread.
I am unable to ping localhost.
ping localhost tries to ping localhost which is defined in DNS.
My /etc/hosts has entry for localhost as
127.0.0.1 loopback localhost.
... (8 Replies)
Discussion started by: chpsam
8 Replies
LEARN ABOUT HPUX
rcsmerge
rcsmerge(1) General Commands Manual rcsmerge(1)
NAME
rcsmerge - merge RCS revisions
SYNOPSIS
rev2] file
DESCRIPTION
incorporates the changes between rev1 and rev2 of an RCS file into the corresponding working file. If is given, the result is printed on
the standard output; otherwise the result overwrites the working file.
A file name ending in is an RCS file name; otherwise it is a working file name. derives the working file name from the RCS file name and
vice versa, as explained in rcsintro(5). A pair consisting of both an RCS and a working file name can also be specified.
rev1 cannot be omitted. If rev2 is omitted, the latest revision on the trunk is assumed. Both rev1 and rev2 can be given numerically or
symbolically.
prints a warning if there are overlaps, and delimits the overlapping regions as explained for the option of co(1). The command is useful
for incorporating changes into a checked-out revision.
EXAMPLES
Suppose you have released revision 2.8 of Assume furthermore that you just completed revision 3.4 when you receive updates to release 2.8
from someone else. To combine the updates to 2.8 and your changes between 2.8 and 3.4, put the updates to 2.8 into file and execute:
Then examine Alternatively, if you want to save the updates to 2.8 in the RCS file, check them in as revision 2.8.1.1 and execute
As another example, the following command undoes the changes between revision 2.4 and 2.8 in your currently checked out revision in
Note the order of the arguments, and that is overwritten.
WARNINGS
does not work for files that contain lines with a single
AUTHOR
was developed by Walter F. Tichy.
SEE ALSO
ci(1), co(1), merge(1), ident(1), rcs(1), rcsdiff(1), rlog(1), rcsfile(4).
rcsmerge(1)