Sponsored Content
Operating Systems Linux Red Hat How to generate UUID for 2nd Ethernet card? Post 302590602 by novaothers on Tuesday 17th of January 2012 02:21:15 AM
Old 01-17-2012
Use system-config-network-tui in your putty session
Select edit the devices
select the new device
assign the ipaddress and gateway
start the network services

~cheers~
 

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies

2. IP Networking

Solaris 9 Ethernet Card Problems

I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem? I am using the command: ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies

3. IP Networking

RedHat and Ethernet card no like each other

I have searched this forum for solution and have drawn a blank... so I come to you for help :) I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies

4. UNIX for Dummies Questions & Answers

Ethernet card problem...

I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies

5. SCO

Issue with a ethernet card

Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message: Fsstat:/dev/boot mounted Mounted /stand filesystem System auditing is not enabled. Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0) Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies

6. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies

7. AIX

Utilization of Ethernet Card

Hi, is it possible to find out network utilization of etherenet card in %? Regards, Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies

8. UNIX for Advanced & Expert Users

Generate UUID for a host

Hello Experts, Is there a way to generate Universally Unique identifiers on all Unix flavours such as Solaris, RHELinux,Suse Linux, MacOS,HP UX etc? If i can get a system command or a system call or an algorithm/script/program to generate a unique identifier, it will be helpful. Thanks in... (1 Reply)
Discussion started by: GajendraSharma
1 Replies

9. Solaris

SUN GIGABIT ETHERNET CARD

Hi, we have SUN Gigabit ethernet cards at the server, both have 2 lines connected but hiw can I found out which cable is on which port before I configure it: the cards has 4 ports , from right to left the cables are connected at the first right then 2 empty then the last at the left side. ... (1 Reply)
Discussion started by: manni2
1 Replies

10. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
SYSTEMD-NETWORKD.SERVICE(8)				     systemd-networkd.service				       SYSTEMD-NETWORKD.SERVICE(8)

NAME
systemd-networkd.service, systemd-networkd - Network manager SYNOPSIS
systemd-networkd.service /lib/systemd/systemd-networkd DESCRIPTION
systemd-networkd is a system service that manages networks. It detects and configures network devices as they appear, as well as creating virtual network devices. To configure low-level link settings independently of networks, see systemd.link(5). systemd-networkd will create network devices based on the configuration in systemd.netdev(5) files, respecting the [Match] sections in those files. systemd-networkd will manage network addresses and routes for any link for which it finds a .network file with an appropriate [Match] section, see systemd.network(5). For those links, it will flush existing network addresses and routes when bringing up the device. Any links not matched by one of the .network files will be ignored. It is also possible to explicitly tell systemd-networkd to ignore a link by using Unmanaged=yes option, see systemd.network(5). When systemd-networkd exits, it generally leaves existing network devices and configuration intact. This makes it possible to transition from the initrams and to restart the service without breaking connectivity. This also means that when configuration is updated and systemd-networkd is restarted, netdev interfaces for which configuration was removed will not be dropped, and may need to be cleaned up manually. CONFIGURATION FILES
The configuration files are read from the files located in the system network directory /lib/systemd/network, the volatile runtime network directory /run/systemd/network and the local administration network directory /etc/systemd/network. Networks are configured in .network files, see systemd.network(5), and virtual network devices are configured in .netdev files, see systemd.netdev(5). SEE ALSO
systemd(1), systemd.link(5), systemd.network(5), systemd.netdev(5), systemd-networkd-wait-online.service(8) systemd 237 SYSTEMD-NETWORKD.SERVICE(8)
All times are GMT -4. The time now is 04:26 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy