Sponsored Content
Operating Systems Linux Red Hat How to generate UUID for 2nd Ethernet card? Post 302590265 by saqlain.bashir on Sunday 15th of January 2012 08:16:14 AM
Old 01-15-2012
How to generate UUID for 2nd Ethernet card?

Dear all,
I have two NIC's on my machine.
UUID for the first interface (eth0) was generated by the machine automatically.
Now I want to generate UUID for the 2nd interface (eth1) please help me out.
Thanks in advance...Smilie
 

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies

2. IP Networking

Solaris 9 Ethernet Card Problems

I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem? I am using the command: ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies

3. IP Networking

RedHat and Ethernet card no like each other

I have searched this forum for solution and have drawn a blank... so I come to you for help :) I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies

4. UNIX for Dummies Questions & Answers

Ethernet card problem...

I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies

5. SCO

Issue with a ethernet card

Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message: Fsstat:/dev/boot mounted Mounted /stand filesystem System auditing is not enabled. Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0) Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies

6. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies

7. AIX

Utilization of Ethernet Card

Hi, is it possible to find out network utilization of etherenet card in %? Regards, Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies

8. UNIX for Advanced & Expert Users

Generate UUID for a host

Hello Experts, Is there a way to generate Universally Unique identifiers on all Unix flavours such as Solaris, RHELinux,Suse Linux, MacOS,HP UX etc? If i can get a system command or a system call or an algorithm/script/program to generate a unique identifier, it will be helpful. Thanks in... (1 Reply)
Discussion started by: GajendraSharma
1 Replies

9. Solaris

SUN GIGABIT ETHERNET CARD

Hi, we have SUN Gigabit ethernet cards at the server, both have 2 lines connected but hiw can I found out which cable is on which port before I configure it: the cards has 4 ports , from right to left the cables are connected at the first right then 2 empty then the last at the left side. ... (1 Reply)
Discussion started by: manni2
1 Replies

10. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
MACHINE-ID(5)							    machine-id							     MACHINE-ID(5)

NAME
machine-id - Local machine ID configuration file SYNOPSIS
/etc/machine-id DESCRIPTION
The /etc/machine-id file contains the unique machine ID of the local system that is set during installation. The machine ID is a single newline-terminated, hexadecimal, 32-character, lowercase machine ID string. When decoded from hexadecimal, this corresponds with a 16-byte/128-bit string. The machine ID is usually generated from a random source during system installation and stays constant for all subsequent boots. Optionally, for stateless systems, it is generated during runtime at boot if it is found to be empty. The machine ID does not change based on user configuration or when hardware is replaced. This machine ID adheres to the same format and logic as the D-Bus machine ID. Programs may use this ID to identify the host with a globally unique ID in the network, which does not change even if the local network configuration changes. Due to this and its greater length, it is a more useful replacement for the gethostid(3) call that POSIX specifies. The systemd-machine-id-setup(1) tool may be used by installer tools to initialize the machine ID at install time. RELATION TO OSF UUIDS
Note that the machine ID historically is not an OSF UUID as defined by RFC 4122[1], nor a Microsoft GUID; however, starting with systemd v30, newly generated machine IDs do qualify as v4 UUIDs. In order to maintain compatibility with existing installations, an application requiring a UUID should decode the machine ID, and then apply the following operations to turn it into a valid OSF v4 UUID. With "id" being an unsigned character array: /* Set UUID version to 4 --- truly random generation */ id[6] = (id[6] & 0x0F) | 0x40; /* Set the UUID variant to DCE */ id[8] = (id[8] & 0x3F) | 0x80; (This code is inspired by "generate_random_uuid()" of drivers/char/random.c from the Linux kernel sources.) HISTORY
The simple configuration file format of /etc/machine-id originates in the /var/lib/dbus/machine-id file introduced by D-Bus. In fact, this latter file might be a symlink to /etc/machine-id. SEE ALSO
systemd(1), systemd-machine-id-setup(1), gethostid(3), hostname(5), machine-info(5), os-release(5), sd-id128(3), sd_id128_get_machine(3) NOTES
1. RFC 4122 https://tools.ietf.org/html/rfc4122 systemd 208 MACHINE-ID(5)
All times are GMT -4. The time now is 01:54 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy