01-12-2012
can you post output of vmstat -v 2 10 taken during a peak time when your run queue is high, iostat -Dl, vmstat -v, vmstat -s outputs please. High runqueues with low cpu utilization in most cases point to IO- or memory problems
Regards
zxmaus
10 More Discussions You Might Find Interesting
1. Solaris
Hi to all,
i have an app on solaris 5.8 writed in C++ (3.2.1) that use multi threading.
Hardware has 8 cpu. When i run my app i note that the average of cpu go at least at 40%, and the performance are not so higher..
There is a cpu limitation on solaris, that dedicate only a part of cpu... (3 Replies)
Discussion started by: Moodie
3 Replies
2. Solaris
Hi All,
In my application malloc is returning NULL even though there is sufficient amount of free memory is available but swap memory is low.
Is this possible that, if free memory is high & swap memory is low, malloc will not be able to allocate memory & return NULL ?:)
Kindly look into... (5 Replies)
Discussion started by: Ritesh Kumar
5 Replies
3. Shell Programming and Scripting
on the file Ftp'd from the mainframe ,do we have any UNIX command to replace mainframe low and values to space or null.
i tried using tr and it doesn't work ...
Thanks (1 Reply)
Discussion started by: rlmadhav
1 Replies
4. Shell Programming and Scripting
Is it possible to have a bash script pick the highest and lowest values of four variables? I've been googling for this but haven't come up with anything. I have a script that assigns variables ($c0, $c1, $c2, and $c3) based on the coretemps from grep/sed statements of sensors. I'd like to also... (5 Replies)
Discussion started by: graysky
5 Replies
5. Shell Programming and Scripting
Hi guys,
i have a question about spliting a binary file into 2 chunks.
First chunk with all high bytes and the second one with all low bytes.
What unix tools can i use? And how can this be performed?
I looked in manpages of split and dd but this does not help.
Thanks (2 Replies)
Discussion started by: basta
2 Replies
6. HP-UX
There might be some problem with my server,
because every morning at 7, it's performance become bad with no DB extra deadlock.
But I just couldn't figure it out.
Please give me some advise, thanks a lot...
According to the CPU performace chart, Daily CPU loading Maximum: 42 %, Average:36%.
... (8 Replies)
Discussion started by: GreenShery
8 Replies
7. UNIX for Dummies Questions & Answers
Need some clarification on this....
1. how are kernel/ user spaces and high/low memory related?
2. What do they all mean when i have the kernel command line as:
"console=ttyS0,115200 root=/dev/sda2 rw mem=exactmap memmap=1M@0 memmap=96M@1M irqpoll"
or
2. what do mem and memmap mean in... (3 Replies)
Discussion started by: dragonpoint
3 Replies
8. AIX
Hi
I am running AIX 5.2. My server is running low on memory. It it using about 1307775 file pages on a total of 1511424 (from vmstat -v).
I looked at the memory yesterday morning, and we had plenty of free memory. I did a backup from Windows (ftp mget command) of a large file selection. From... (5 Replies)
Discussion started by: fredrivard
5 Replies
9. Red Hat
Hi team
I have three physical servers running on Red Hat Enterprise Linux Server release 6.2 with the following memory conditions:
# cat /proc/meminfo | grep -i mem
MemTotal: 8062888 kB
MemFree: 184540 kB
Shmem: 516 kB
and the following swap conditions:
... (6 Replies)
Discussion started by: hedkandi
6 Replies
10. UNIX for Advanced & Expert Users
Could I please get some recommendations of a linux live cd for low memory? (1 Reply)
Discussion started by: cokedude
1 Replies
iostat(1) General Commands Manual iostat(1)
NAME
iostat - Reports I/O statistics
SYNOPSIS
iostat [drive...] [interval] [count]
OPERANDS
Forces iostat to display specific drives. If drive is not specified (or the specified drive does not exist on the system or cluster,
iostat displays the first two drives (even if more than two disk drives are configured in the system). Causes iostat to report once each
interval seconds. The first report is for all time since the system was last booted, and each subsequent report is for the last interval
only.The value must not be 0. Specifies the number of reports. For example, iostat 1 10 would produce 10 reports at 1-second intervals.
You cannot specify count without interval because the first numeric argument to iostat is assumed to be interval.
DESCRIPTION
The iostat command reports the following information: For terminals (collectively), the number of characters read and written per second.
For each disk, the number of transfers per second and bytes transferred per second (in kilobytes). For the system, the percentage of time
the system has spent in user mode, in user mode running low priority (nice) processes, in system mode, and idling.
To compute this information, iostat counts data transfer completions, the number of words transferred for each disk, and the collective
number of input and output characters for terminals. Also, each sixtieth of a second, iostat examines the state of each disk and makes a
tally if the disk is active.
When you issue an iostat command on a cluster member, it displays statistics only for those disks that are local to the member and that
member's usage of those shared disks that it has mounted. It displays 0 for other disks in the cluster (those it doesn't have mounted),
regardless of whether they are on the shared bus or are local to some other member.
EXAMPLES
The output from this example displays cpu, terminal, and disk statistics for the first two disks on the system providing 5 reports at 1
second intervals:
# iostat 1 5
tty floppy1 dsk9 cpu
tin tout bps tps bps tps us ni sy id
0 3 0 0 0 0 1 0 4 95
4 58 0 0 0 0 1 0 2 97
1 53 0 0 0 0 0 0 2 98
5 59 0 0 0 0 1 0 1 98
6 60 0 0 0 0 1 0 2 97
The second example specifies device names in the command:
# iostat dsk2 dsk3 cdrom2
tty dsk2 cdrom2 dsk3 cpu
tin tout bps tps bps tps bps tps us ni sy id
0 13 11 5 5 2 2427 1213 0 1 1 98
SEE ALSO
Commands:vmstat(1)
iostat(1)