how can i show the value when i divide a number where the dividend is greater then the divisor. for example...
3 divided by 15 ---> let x=3/15
when i do this in the shell environment it gives me an output of 0.
please help me.
thanks. (3 Replies)
I have a doubt with an error message, and i want to be sure if this is a normal situation or not.
Situation: I was formating and installing a SCSI 36Gb HD with UNIX SCO 5.05, the problem happens when is making the division and filesystem on disk 1, and the message error is "Exit value 139... (1 Reply)
hi
I am having two variables namely a=7 & b=8. I have to subtract these two variables. I am using the command
c=`expr $a / $b`
When I check the value of c, it comes out to be zero.
Please help.
Regards
Rochit (9 Replies)
Hi,
I am writing a script that among other things will be checking for various files on mount points. One of the conditions is that unless the server has failed over the df command will show root ( / ). If when checking the files the script comes across /, I want it to skip it, otherwise to... (2 Replies)
i have a script that is doing the following:
awk 'BEGIN {FS=","} ; {printf("%.10f",($5 - $2)/(3 * $3))}' data > test
now some records in $3 contain zeroes. i don't want to remove those records. is it possible to check for division by zero and then write a "N/A" for that record in the o/p... (2 Replies)
Hello,
I am searching for a way to calculate for example 10/100 within a shellscript and the result should be 0.1 and not just 0.
Every alternative i tried just results 0
Thank you in advance
2retti (6 Replies)
I received error "awk: division by zero" while executing the following statement.
SunOS 5.10 Generic_142900-15 sun4us sparc FJSV,GPUZC-M
echo 8 | awk 'END {printf ("%d\n",NR/$1 + 0.5);}' file1.lst
awk: division by zero
Can someone provide solution?
Thanks
Please use code... (11 Replies)
I have a function that outputs 3 lines for each result and I want to know how many results there are.
so for example
function | wc -l
24
but I want to see the result 8.
so is there a easy way to divide the result? (5 Replies)
I have two text files T1 and T2
T1 looks as follows
Name All Maths Science English Social
Anie 48/18 = 2.7 44/17 = 2.6 20/6 = 3.3 24/11 = 2.2 NA
Edwin ... (4 Replies)
Discussion started by: andrewps
4 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)