12-20-2011
why a video card in a server?
9 More Discussions You Might Find Interesting
1. Solaris
Hi there
the Sunfire X4100 has a great tool that you can get to from BIOS called the configuration utility which allows you to set up Disk mirroring (RAID 1) before the OS sees it, which is great and it works a treat, however, we have a large datacentre across multiuple sites and I need to find... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
2. Solaris
Hi there
I am running solaris 10 on an SunFire x4100 ...(x86 box) Could anybody tell me if there is a way I can check the firmware revision without taking the box down to do it ...eeprom doesnt give me the info I require
Cheers (0 Replies)
Discussion started by: hcclnoodles
0 Replies
3. Solaris
Hi everyone,
I have a problem which looks like very simple. My SunFire X4100 have 2 disk slots: HDD0, HDD1 and 1 hard disk. I installed OS on the hard disk at HDD0 and now i want to boot it at HDD1.
When i change BIOS and begin boot at HDD1 it reset after i chose Solaris 10 at OS selecting... (3 Replies)
Discussion started by: tien86
3 Replies
4. Solaris
I have looked all over the bios configuration to enable hardware virtualization and found nothing. Could someone tell if this server support it and if so where I go to enable that feature. By the way this is a x86 server. (0 Replies)
Discussion started by: jsandova
0 Replies
5. Hardware
hi
please how to know that a sun x4100 m2 server has one or two processors installed ?? the OS installed on this server is windows 2003 Enterprise Edition.
thanks (2 Replies)
Discussion started by: bahjatm
2 Replies
6. OS X (Apple)
Howdy
I am trying to install links2 with graphics support on snow leopard 10.6.8 (xcode installed). I have had the program running last year, also installed from source - but then I had installed some image libraries with mac ports and fink - cannot reproduce that setup. Plus I would like to not... (6 Replies)
Discussion started by: butterbaerchen
6 Replies
7. Ubuntu
Hi
I have two Sun Fire X4100 machines with Ubuntu 12.04 installed on them.
I am able to configure the Net Mgt port with an IP address and access the ILOM from the browser. I can also boot the Ubuntu installed and redirect the output.
The issue i have is that when i configure the network... (0 Replies)
Discussion started by: kaf3773
0 Replies
8. Solaris
Hi,
I am currently on Sunfire X4100. This server doesn't have CDROM drive. Also I can't get to the OK prompt. From my laptop, I am connected to the management port using the Cisco Blue cable.
Please advise how can I get to the OK prompt. Also the server is so loud. Will the FAN cool... (1 Reply)
Discussion started by: samnyc
1 Replies
9. Hardware
I have a problem,
I have been installing Redhat Interprise Linux on X4100 M2 Server, when system is reboot after install, the server is restart (reboot) again (alias unlimited).
The bios system show message error "Multi-bit ECC Error" and "bank interleave requested but not enable"
I have... (5 Replies)
Discussion started by: hhaswan
5 Replies
LEARN ABOUT DEBIAN
get_gfx_mode_list
get_gfx_mode_list(3alleg4) Allegro manual get_gfx_mode_list(3alleg4)
NAME
get_gfx_mode_list - Obtains a list of available video modes. Allegro game programming library.
SYNOPSIS
#include <allegro.h>
GFX_MODE_LIST *get_gfx_mode_list(int card);
DESCRIPTION
Attempts to create a list of all the supported video modes for a certain graphics driver, made up from the GFX_MODE_LIST structure, which
has the following definition:
typedef struct GFX_MODE_LIST
{
int num_modes;
GFX_MODE *mode;
} GFX_MODE_LIST;
The mode entry points to the actual list of video modes.
typedef struct GFX_MODE
{
int width, height, bpp;
} GFX_MODE;
This list of video modes is terminated with an { 0, 0, 0 } entry.
Note that the card parameter must refer to a _real_ driver. This function fails if you pass GFX_SAFE, GFX_AUTODETECT, or any other "magic"
driver.
RETURN VALUE
Returns a pointer to a list structure of the type GFX_MODE_LIST or NULL if the request could not be satisfied.
SEE ALSO
destroy_gfx_mode_list(3alleg4), set_gfx_mode(3alleg4), set_color_depth(3alleg4)
Allegro version 4.4.2 get_gfx_mode_list(3alleg4)