Sponsored Content
Operating Systems Solaris Could not start installation using jumpstart Post 302581207 by beta17 on Monday 12th of December 2011 10:59:19 AM
Old 12-12-2011
starting the installation with following commands helps sometimes:
Code:
boot net -v install

and check this site:
Home - Jumpstart Enterprise Toolkit - wikis.sun.com
 

10 More Discussions You Might Find Interesting

1. Solaris

Jumpstart installation problem.

We are installing Solaris 9 with Jumpstart ...facing problems.. Problem is .it is prompting for questions, even though we set the Sysidcfg and class files properly. when we give "boot net - install" at OK prompt, it is coming till "The system is coming up. Please wait" After that it... (5 Replies)
Discussion started by: b_manu78
5 Replies

2. Solaris

Solaris 10 installation over WAN using jumpstart

I am trying to install Solaris 10 OS using jumpstart over WAN. I have configured the jumpstart server with apache server and created all the necessary configurations and files. When i WAN boot my target machine, it gets booted using wanboot, it downloads the miniroot from the jumpstart server, but... (3 Replies)
Discussion started by: hemalsid
3 Replies

3. Solaris

Jumpstart Solaris Installation Program screen

Hi! I'm trying to skip the installation welcome screen (actually the first three screens: The Solaris Installation Program screen, Identify This System screen and date and time settings - not timezone settings). Everything else runs automaticly from jumpstart except these three screens, just... (6 Replies)
Discussion started by: Luka
6 Replies

4. Solaris

Flash installation with Jumpstart

I get following error while doing a flash installation. I 'm trying to deploy a flash archive created by our engineering team. I 'm trying to install it with ZFS root and the profile which i using is as following #more flash_profile_test install_type flash_install archive_location nfs... (3 Replies)
Discussion started by: fugitive
3 Replies

5. Solaris

jumpstart installation

hi friends, i dont know how to install jumpstart . i have solaris cds( 5 nos.). i tried to install jumpstart but there is no setup_install_server file. What i want to do for installing jumpstart server please help me thanks to all (8 Replies)
Discussion started by: sijocg
8 Replies

6. Solaris

Jumpstart Installation from X86 machine

Hi friends , i have on ultra 10 Sparc machine . Due to some problem my OS is fully corrupted , so i am planning to install again but my problem is the cd drive in Ultra 10 machine is not working. Now i am planning to use Jumpstart installation method to install my server. But i... (4 Replies)
Discussion started by: vr_mari
4 Replies

7. Solaris

Jet/Jumpstart installation freezing

Hi guys, I have a problem with installing new Solaris servers via jet/jumpstart (tried both). I`ve configured server, created profile for a client, issued {1} boot net -v install and went to get some cofee... After I came back, client was able to load system from server, get IP and,... (4 Replies)
Discussion started by: masloff
4 Replies

8. Solaris

Solaris x86 installation using jumpstart does not local boot ( boot from hdd)

I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies

9. Solaris

help me! jumpstart installation error

Hi actualy my two machines are sun sparc ultra 60. Both are same configuration. I am trying jumpstart Installation in my two machines, i got no errors in server side but in the client side actually it detects the server machine with correct hostname and domainname but after showed that it will... (2 Replies)
Discussion started by: Grovestreet
2 Replies

10. Solaris

Problem in configuring jumpstart installation

I am trying to configuring jumpstart configuration. Please find below sysidcfg configuration file output bash-3.2# cat sysidcfg terminal=vt100 network_interface=nxge0 { primary hostname=sun1 ip_address=192.168.11.10 \ protocol_ipv6=no netmask=255.255.255.0 default_route=192.168.11.7}... (5 Replies)
Discussion started by: sb200
5 Replies
uri_urn(3tcl)					    Tcl Uniform Resource Identifier Management					     uri_urn(3tcl)

__________________________________________________________________________________________________________________________________________________

NAME
uri_urn - URI utilities, URN scheme SYNOPSIS
package require Tcl 8.2 package require uri::urn ?1.1.2? uri::urn::quote url uri::urn::unquote url _________________________________________________________________ DESCRIPTION
This package provides two commands to quote and unquote the disallowed characters for url using the urn scheme, registers the scheme with the package uri, and provides internal helpers which will be automatically used by the commands uri::split and uri::join of package uri to handle urls using the urn scheme. COMMANDS
uri::urn::quote url This command quotes the characters disallowed by the urn scheme (per RFC 2141 sec2.2) in the url and returns the modified url as its result. uri::urn::unquote url This commands performs the reverse of ::uri::urn::quote. It takes an urn url, removes the quoting from all disallowed characters, and returns the modified urls as its result. BUGS, IDEAS, FEEDBACK This document, and the package it describes, will undoubtedly contain bugs and other problems. Please report such in the category uri of the Tcllib SF Trackers [http://sourceforge.net/tracker/?group_id=12883]. Please also report any ideas for enhancements you may have for either package and/or documentation. KEYWORDS
rfc 2141, uri, url, urn CATEGORY
Networking uri 1.1.2 uri_urn(3tcl)
All times are GMT -4. The time now is 06:12 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy