12-09-2011
If they're using different gateways, internet traffic should just go where it's proper destination is. (Unless you're using a proxy, which would mess up its ability to tell which connection outgoing traffic belongs to.) The switch shouldn't care.
If both routers are serving DHCP, they'll of course interfere with each other when plugged into the same switch. Only one of them should be allowed to serve DHCP, probably your 'client' connection, configure your server statically.
Local traffic would be trickier. They'll be running on the same wire, so they could talk directly if they tried, but not being on the same subnet means they'll just forward it to their gateway instead, which won't work. The switch, which doesn't care at all about IP addresses, won't notice or care.
You could make it all one big happy 255.255.0.0 subnet, which would allow 192.0.0 and 192.0.10 to communicate without routing. Or you could give your clients static routes to talk to the other subnet. Or your server could be given 192.0.0 and 192.0.10 addresses on the same card so your clients don't have to talk to a "foreign" subnet.
Last edited by Corona688; 12-09-2011 at 12:13 PM..
8 More Discussions You Might Find Interesting
1. Linux
how can i see active network connections (1 Reply)
Discussion started by: youmna
1 Replies
2. IP Networking
Hello,
I have a centralized syslog server, and am wondering if there is a way to log all network connections to it (Primarily incoming, such as FTP, httpd, SSH, etc). Essentially what I would like is to get the information seen in netstat or lsof logged line by line, realtime. Is there a... (3 Replies)
Discussion started by: abstrcrndm
3 Replies
3. Linux
Hi,
I have a question on web servers and network switches.
Why a network switch should support certificate management, that means generating public and private keys... installing a certificate etcetra.
Regards
Chaitanya. :b: (4 Replies)
Discussion started by: chaitus.28
4 Replies
4. IP Networking
I rotate between a static lan, dhcp lan, and various wireless networks daily. Is there a way to set preferred network connections? I use some static ip's daily, some static ip's like once a month, and almost never use the dhcp lan. The same I do with my various wireless networks. Some I use daily... (0 Replies)
Discussion started by: cokedude
0 Replies
5. Shell Programming and Scripting
Could you help me writing a script showing which network connections are currently active?
Means output should be something like:
"eth0, wlan1, wlan3"
Problem:
The output is supposed to happen on a 16x2 LCD Display.
Currently I am doing a "Ifconfig" as output, but its too fast for the... (2 Replies)
Discussion started by: lordofazeroth
2 Replies
6. UNIX for Advanced & Expert Users
I have a static IP 47.21.154.146 and two computers which I wish to talk to each other. The two IPs are 198.168.1.5 and 198.168.1.6.
How do I do it. For example ls from one computer to the other.
TIA (8 Replies)
Discussion started by: Meow613
8 Replies
7. Red Hat
i have been learning linux from some time for linux plus exam and learned SSH protocol and have practised to connect to remote computer within Lan network and able to sucesssfully connect it .
using
ssh username@hostname
But i wish to ask how do i use same ssh protocol to connect to other ... (6 Replies)
Discussion started by: lobsang
6 Replies
8. Solaris
hello, I have a problem when configuring the network at the LDOM level, on a SPARC-Enterprise-T5120 machine
The network goes through VLAN 503 (level, network tagget)
And I need to give network to the guest domain: madarrwebsol10
I hope someone can bring some light ....
Excuse my English ...
... (4 Replies)
Discussion started by: Wittman
4 Replies
LEARN ABOUT OPENSOLARIS
ce
CE(4) BSD/i386 Kernel Interfaces Manual CE(4)
NAME
ce -- driver for synchronous Cronyx Tau-PCI/32 WAN adapters
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device ce
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_ce_load="YES"
Additional options:
device sppp
options NETGRAPH
options NETGRAPH_CRONYX
DESCRIPTION
The ce driver needs either sppp(4) or netgraph(4). Which one to use is determined by the NETGRAPH_CRONYX option. If this option is present
in your kernel configuration file, the ce driver will be compiled with netgraph(4) support. Otherwise, it will be compiled with sppp(4) sup-
port.
Refer to sconfig(8) for information about the ce adapter configuration.
HARDWARE
The ce driver supports the following models of Tau-PCI/32 WAN adapters:
Cronyx Tau-PCI/32 two fractional/unframed E1 interfaces, with 32 HDLC channels shared between them with total adapter throughput 2048
kbps.
Cronyx Tau-PCI/32-Lite
single fractional/unframed E1 interface, with 32 HDLC channels.
SEE ALSO
cp(4), ctau(4), cx(4), sppp(4), ifconfig(8), sconfig(8), spppcontrol(8)
HISTORY
The ce driver was added in FreeBSD 6.2, FreeBSD 5.5 and FreeBSD 4.11. The ce driver for previous versions of FreeBSD is available from
http://www.cronyx.ru/.
BSD January 30, 2006 BSD