12-02-2011
What architecture or OS are you talking about?
What do you mean by "connect to network"? Are you talking of your PC?
10 More Discussions You Might Find Interesting
1. Solaris
Yes. But just wait a bit. How to do it via system calls? I'm just a newbie in Unix\Linux\Solaris e.t.c. programming. Can anyone help me? I need an advice probably how to do it or may be what API to read... :) Please, help... (2 Replies)
Discussion started by: LocalStorm
2 Replies
2. IP Networking
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
3. SCO
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
4. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (0 Replies)
Discussion started by: snakernetb
0 Replies
5. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (1 Reply)
Discussion started by: snakernetb
1 Replies
6. Solaris
I got second IOU in my M5000 but not able bring internal network interfcae .. ike i don't get link on those 2 interfaces .. and the same network cable plugged in PCI network card it works like a charm Is there any special way to enable the internal IOU interfaces or i have bad nics ? (8 Replies)
Discussion started by: fugitive
8 Replies
7. Debian
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies
8. UNIX for Advanced & Expert Users
All, I have a quad NIC on a V880 running Solaris 9. I've heard you can bond interfaces together and get better throughput. I found this link that seems to describe the process well. However, the command mentioned (dladm) is missing. Is there some package I need to install to get this command? Thx.... (2 Replies)
Discussion started by: agcodba
2 Replies
9. AIX
Hi,
I would like to know after the installation of vio server. how many logical network interfaces will be created on vio server if I am having two physical interfaces on vio server.
I am asking this question because I would like know to on the basis of logical network interfaces creation on... (0 Replies)
Discussion started by: manoj.solaris
0 Replies
10. Linux
I just ran sudo service networking start on Ubuntu 16.00 and came out with error message
Job for networking service failed because control process exited with error code see systemctl status networking.service
I tried to also run this command
systemctl status networking.service
I also got an... (4 Replies)
Discussion started by: DOkuwa
4 Replies
LEARN ABOUT SUNOS
snmpgetnext
snmpgetnext(1M) System Administration Commands snmpgetnext(1M)
NAME
snmpgetnext - communicate with a network entity using SNMP GETNEXT requests
SYNOPSIS
snmpgetnext [-Cf] [common options] oid [oid...]
DESCRIPTION
The snmpgetnext utility is an SNMP application that uses the SNMP GETNEXT request to query for information on a network entity. You can
specify one or more object identifiers (OIDs) as arguments on the command line. Each variable name must be specified in the format speci-
fied in snmp_variables(4) . For each variable, the one that is lexicographically "next" in the remote entity's MIB is returned.
For example, the command:
# snmpgetnext -c public zeus interfaces.ifTable.ifEntry.ifType.1
retrieves the variable interfaces.ifTable.ifEntry.ifType.2:
interfaces.ifTable.ifEntry.ifType.2 = softwareLoopback(24)
If the network entity has an error processing the request packet, an error packet is returned and a message displayed. The message indi-
cates the way in which the request was malformed.
OPTIONS
The following options are supported:
-Cf
If -Cf is not specified, some applications (including snmpget(1M) and snmpgetnext) attempt to fix errors returned by the agent that you
were talking to and resend the request. The -Cf option suppresses this fix-and-resend feature.
Fix-and-resend is useful if you specified a nonexistent OID in your request and you are using SNMPv1, which requires "all or nothing"
types of requests.
In addition to this option, snmpgetnext takes the common options described in the snmpcmd(1M) manual page.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWsmcmd |
+-----------------------------+-----------------------------+
|Interface Stability |External |
+-----------------------------+-----------------------------+
EXIT STATUS
0
Successful completion.
1
A usage syntax error. A usage message is displayed. Also used for timeout errors.
2
An error occurred while executing the command. An error message is displayed.
SEE ALSO
snmpcmd(1M), snmpget(1M), snmp_variables(4), attributes(5)
SunOS 5.10 20 Jan 2004 snmpgetnext(1M)