12-02-2011
What architecture or OS are you talking about?
What do you mean by "connect to network"? Are you talking of your PC?
10 More Discussions You Might Find Interesting
1. Solaris
Yes. But just wait a bit. How to do it via system calls? I'm just a newbie in Unix\Linux\Solaris e.t.c. programming. Can anyone help me? I need an advice probably how to do it or may be what API to read... :) Please, help... (2 Replies)
Discussion started by: LocalStorm
2 Replies
2. IP Networking
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
3. SCO
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
4. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (0 Replies)
Discussion started by: snakernetb
0 Replies
5. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (1 Reply)
Discussion started by: snakernetb
1 Replies
6. Solaris
I got second IOU in my M5000 but not able bring internal network interfcae .. ike i don't get link on those 2 interfaces .. and the same network cable plugged in PCI network card it works like a charm Is there any special way to enable the internal IOU interfaces or i have bad nics ? (8 Replies)
Discussion started by: fugitive
8 Replies
7. Debian
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies
8. UNIX for Advanced & Expert Users
All, I have a quad NIC on a V880 running Solaris 9. I've heard you can bond interfaces together and get better throughput. I found this link that seems to describe the process well. However, the command mentioned (dladm) is missing. Is there some package I need to install to get this command? Thx.... (2 Replies)
Discussion started by: agcodba
2 Replies
9. AIX
Hi,
I would like to know after the installation of vio server. how many logical network interfaces will be created on vio server if I am having two physical interfaces on vio server.
I am asking this question because I would like know to on the basis of logical network interfaces creation on... (0 Replies)
Discussion started by: manoj.solaris
0 Replies
10. Linux
I just ran sudo service networking start on Ubuntu 16.00 and came out with error message
Job for networking service failed because control process exited with error code see systemctl status networking.service
I tried to also run this command
systemctl status networking.service
I also got an... (4 Replies)
Discussion started by: DOkuwa
4 Replies
LEARN ABOUT OPENSOLARIS
network-admin
network-admin(1) User Commands network-admin(1)
NAME
network-admin - Basic administration of network interfaces.
SYNOPSIS
network-admin [--configure=INTERFACE] [--configure-type=TYPE] [gnome-std-options]
DESCRIPTION
network-admin enumerates the interfaces available to the user and provides a mechanism for configuring these interfaces as static-IP or
DHCP. It's also possible to select which interfaces should be enabled on boot.
network-admin also allows you configure the systems hostname, DNS options and hosts using the user interface.
OPTIONS
The following options are supported:
-c, --configure=INTERFACE Configure a specific network interface (e.g. ath0 or bge0).
-t, --configure-type=TYPE Configure the first network interface of a specific type (e.g. ethernet or wireless).
gnome-std-options Standard options available for use with most GNOME applications. See gnome-std-options(5) for more informa-
tion.
EXAMPLES
Example 1: Running the main application.
example% network-admin
Example 2: Configuring the ath0 network interface.
example% network-admin --configure=ath0
Example 3: Configuring the first ethernet interface.
example% network-admin --configure-type=ethernet
EXIT STATUS
The following exit values are returned:
0 Application exited successfully
>0 Application exited with failure
FILES
The following files are used by this application:
/usr/bin/network-admin Executable for network interface configuration.
/etc/inet/gnome-system-tools Storage location for network configuration files when not active on boot.
/var/spool/setup-tool-backends/backup/network
Backup directory for files that are modified.
/var/spool/setup-tool-backends/data/network
Where "Location" profiles are stored.
/var/run/setup-tool-backends/debug/network
Debug logs can be found under here.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWgnome-system-tools |
+-----------------------------+-----------------------------+
|Interface stability |Uncommitted |
+-----------------------------+-----------------------------+
SEE ALSO
Latest version of the GNOME Desktop User Guide for your platform.
users-admin(1), shares-admin(1), services-admin(1), time-admin(1), gnome-std-options(5), ifconfig(1M), hosts(4), nsswitch.conf(4),
resolv.conf(4), attributes(5)
NOTES
This tool can only be used to manage physical network devices as returned by the "dladm show-dev" command, it does not support configura-
tion of more complex configurations.
There is currently no support for enterprise name services such as YP/NIS, NIS+ or LDAP. There is also no support for anything but the
global zone.
Written by Darren Kenny, Sun Microsystems Inc., 2006.
SunOS 5.11 6 Nov 2006 network-admin(1)