12-02-2011
/etc/network/interfaces
i need a one liner command that writes in /var/log/net.log the date when i connect to the network and when i disconect ..i know that i need to write somethin in /etc/network/interfaces but idk what ! please help
10 More Discussions You Might Find Interesting
1. Solaris
Yes. But just wait a bit. How to do it via system calls? I'm just a newbie in Unix\Linux\Solaris e.t.c. programming. Can anyone help me? I need an advice probably how to do it or may be what API to read... :) Please, help... (2 Replies)
Discussion started by: LocalStorm
2 Replies
2. IP Networking
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
3. SCO
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies
4. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (0 Replies)
Discussion started by: snakernetb
0 Replies
5. AIX
Hi all, this is my first post on this forum. My main problem is this:
I have a NIM server that I am trying to configure two interfaces on. One interface is for an internal Admin VLAN, the other is so that the server can use SUMA to pull updates. The problem is that I need help w/ the routing.... (1 Reply)
Discussion started by: snakernetb
1 Replies
6. Solaris
I got second IOU in my M5000 but not able bring internal network interfcae .. ike i don't get link on those 2 interfaces .. and the same network cable plugged in PCI network card it works like a charm Is there any special way to enable the internal IOU interfaces or i have bad nics ? (8 Replies)
Discussion started by: fugitive
8 Replies
7. Debian
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies
8. UNIX for Advanced & Expert Users
All, I have a quad NIC on a V880 running Solaris 9. I've heard you can bond interfaces together and get better throughput. I found this link that seems to describe the process well. However, the command mentioned (dladm) is missing. Is there some package I need to install to get this command? Thx.... (2 Replies)
Discussion started by: agcodba
2 Replies
9. AIX
Hi,
I would like to know after the installation of vio server. how many logical network interfaces will be created on vio server if I am having two physical interfaces on vio server.
I am asking this question because I would like know to on the basis of logical network interfaces creation on... (0 Replies)
Discussion started by: manoj.solaris
0 Replies
10. Linux
I just ran sudo service networking start on Ubuntu 16.00 and came out with error message
Job for networking service failed because control process exited with error code see systemctl status networking.service
I tried to also run this command
systemctl status networking.service
I also got an... (4 Replies)
Discussion started by: DOkuwa
4 Replies
RTMON(8) System Manager's Manual RTMON(8)
NAME
rtmon - listens to and monitors RTnetlink
SYNOPSIS
rtmon [ options ] file FILE [ all | LISTofOBJECTS ]
DESCRIPTION
This manual page documents briefly the rtmon command.
rtmon listens on netlink socket and monitors routing table changes.
rtmon can be started before the first network configuration command is issued. For example if you insert:
rtmon file /var/log/rtmon.log
in a startup script, you will be able to view the full history later. Certainly, it is possible to start rtmon at any time. It prepends
the history with the state snapshot dumped at the moment of starting.
OPTIONS
rtmon supports the following options:
-Version
Print version and exit.
help Show summary of options.
file FILE [ all | LISTofOBJECTS ]
Log output to FILE. LISTofOBJECTS is the list of object types that we want to monitor. It may contain 'link', 'address', 'route'
and 'all'. 'link' specifies the network device, 'address' the protocol (IP or IPv6) address on a device, 'route' the routing table
entry and 'all' does what the name says.
-family [ inet | inet6 | link | help ]
Specify protocol family. 'inet' is IPv4, 'inet6' is IPv6, 'link' means that no networking protocol is involved and 'help' prints
usage information.
-4 Use IPv4. Shortcut for -family inet.
-6 Use IPv6. Shortcut for -family inet6.
-0 Use a special family identifier meaning that no networking protocol is involved. Shortcut for -family link.
USAGE EXAMPLES
# rtmon file /var/log/rtmon.log
Log to file /var/log/rtmon.log, then run:
# ip monitor file /var/log/rtmon.log
to display logged output from file.
SEE ALSO
ip(8)
AUTHOR
rtmon was written by Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>.
This manual page was written by Michael Prokop <mika@grml.org>, for the Debian project (but may be used by others).
RTMON(8)