12-01-2011
I know that in the past on a Power 5 box, the virtual console was able to map out to the physical serial port allowing serial console access. Just saying. I think that still holds true. It's not the typical way... but it does mostly work. I think I had problem getting out of a session and back to the "top" though... but if it's just one lpar... then you're fine IMHO.
10 More Discussions You Might Find Interesting
1. AIX
I am trying to run the lscod command against an HMC that has managed system names with spaces.
Tried enclosing the managed system names in quotes; single and double.
How do I get the command to run?
ssh hmcname lscod -m 'managed system 1' -t cap -r proc -c cuod
Thanks,
~Donavon (0 Replies)
Discussion started by: djlerman
0 Replies
2. AIX
Steps to upgrade AIX TL ( technology Level ) / Maintenance Level in AIX ( including Firmware HMC VIOS )
This article or post covers upgrades for
- Hardware Management Console ( HMC )
- Firmware ( also known as microcode )
- VIO ( Virtual I/O Server = PowerVM )
- AIX Version, Technology... (2 Replies)
Discussion started by: filosophizer
2 Replies
3. AIX
I started the AIX install with a fiber channel disk, and let it run:
restricted by GSA ADP Schedule Contract with IBM Corp.
. . . . . << End of copyright notice for perfagent.tools >>. . . .
... (2 Replies)
Discussion started by: Gideon1a
2 Replies
4. AIX
I have an HMC that I'm looking to upgrade from V7.3.4.0 SP2 to the latest version V7.7.6.0. I'm looking at the firmware levels of the systems attached to this HMC, and all of the systems have compatible firmware revisions but there are two that have been update recently and the platform IPL level... (10 Replies)
Discussion started by: acascianelli
10 Replies
5. AIX
Hi ,
I would like to access the cd drive of , i have power series server , and have lpars .
I try to install AIX in an lpar via HMC, but it can't access the cd drive.
how i can make installtion or make the the cd drive accessible in hmc or in power series server?
Thanks in advance (2 Replies)
Discussion started by: prpkrk
2 Replies
6. AIX
Hi,
For installing aix on power series , do i need to install hmc first?
or i can connect hmc after?
Rgs, (7 Replies)
Discussion started by: prpkrk
7 Replies
7. AIX
Trying to get the IP address of the HMC connected to some servers running AIX 6 and 7. I thought this would be as easy as running 'lsrsrc IBM.MCP IPAddresses', but when I run that command, the resource is empty. Is there some where else I should be looking, or is there a reason why this resource... (5 Replies)
Discussion started by: acascianelli
5 Replies
8. AIX
Hi Experts
So we have two data center .I upgraded the HMC in one datacenter, very easy no problem, but in the second datacenter we have dual HMC connection. I am looking at the document from the ibm documentation. I found something that I am not comfortable following. which is this : Physically... (2 Replies)
Discussion started by: JME2015
2 Replies
9. AIX
Hey All,
I have running dual VIOS on a P9 systems, and just created a new LPAR profile. My objective is to create LPAR Client VFC adapters, and then DLPAR VFC Server adapters on the VIOS.
In the HMC v9 Enhanced GUI, I have DLPAR a VFC adapter to both VIOS, however, you can't specify the... (1 Reply)
Discussion started by: aixkidbee
1 Replies
10. AIX
hello
P6 was managed by HMC, tried to install on it VIOS 2.2.6
and got this error message
Hosting requires a hosting partition -- boot not permitted
vios-4 - imgbb.com
then after creating an lpar in HMC got this message
B2001230
vios-3 - imgbb.com
anyone know how to solve this... (3 Replies)
Discussion started by: filosophizer
3 Replies
ports(7) Miscellaneous Information Manual ports(7)
NAME
ports, port_names - Device (tty and lp) names for serial and parallel ports
SYNOPSIS
Default Serial Ports:
/dev/tty00
/dev/tty01 (not present on a single-port system)
Parallel Port:
/dev/lp0
DESCRIPTION
AlphaStation and AlphaServer systems provide one or two 9-pin serial communication ports. These ports are usually labelled 1 (COMM1) and 2
(COMM2), but they may be identified by different icons. Using the appropriate serial cable and terminator, you can connect a serial
printer, external modem, or character-cell terminal to a serial port. Most AlphaStation and AlphaServer systems also provide one parallel
port, for use with a parallel printer.
When you add a device to your system, the installation documentation may instruct you to map the device pathname to the port. These
devices are located in the /dev directory.
For serial-line ports, the two default device pathnames are: This pathname always maps to 1, COMM1, the lowest port number, an icon for a
terminal console, or the only serial port (on a single-port system). This pathname always maps to 2, COMM2, the next numbered port, or (if
one serial port is labeled with an icon for a terminal console) the remaining serial port.
If your system hardware has been extended to include additional serial ports, the pathnames /dev/tty02, /dev/tty03, and so forth, may also
be available to you. However, most systems have only /dev/tty00 and /dev/tty01 as the device pathnames for serial ports.
The one parallel port on an AlphaStation or AlphaServer may be labeled with the word printer or a printer icon. On some systems, the paral-
lel port may not be labeled. The device pathname for the parallel port is /dev/lp0. Currently, Tru64 UNIX does not fully support parallel
printers, so fewer devices are connected to this port as compared to serial ports.
If you are connecting a terminal console to your system, it must be connected to the serial port mapped to /dev/tty00. For other serial
devices, it does not matter which of the serial ports you choose for the connection. For example, suppose you are setting up a system that
has two serial ports, labeled 1 and 2. You intend to use a serial-line terminal rather than a workstation monitor as the system console and
also want to connect a serial-line printer to the system. In this case, you must connect the terminal to the port labeled 1 (with the
device pathname /dev/tty00). Therefore, you must connect the printer to the remaining port labeled 2 (with the device pathname /dev/tty01).
If, for the same type of system, you intend to use a workstation monitor as the system console, it does not matter which serial port you
use for a serial-line printer or modem. In other words, you can connect the printer to either port 1 (with pathname /dev/tty00) or port 2
(with pathname /dev/tty01). When prompted to enter a /dev/tty** pathname by the lprsetup script or the Print configuration tool in the CDE
Application Manager, you would specify /dev/tty00 if you connected the printer to port 1 or /dev/tty01 if you connected the printer to port
2.
See the System Administration manual for more information on setting up consoles (including remote consoles) and printers. See the
modem(7) reference page for more information on setting up modems.
SEE ALSO
Commands: lprsetup(8)
Devices: ace(7), modem(7)
System Administration delim off
ports(7)