Sponsored Content
Full Discussion: SVM ISSUE...
Operating Systems Solaris SVM ISSUE... Post 302578043 by bartus11 on Wednesday 30th of November 2011 02:59:14 PM
Old 11-30-2011
What does this output:
Code:
iostat -xn ssd2

 

10 More Discussions You Might Find Interesting

1. Solaris

How do you remove a RAID 5 under SVM?

I have this setup, i can only find docs to unmirror a raid 1 set, how do you get rid of a raid 5 set? the same way? metadetach and metaclear? d8: RAID State: Okay Interlace: 32 blocks Size: 142245693 blocks (67 GB) Original device: Size: 142247872 blocks (67 GB) ... (2 Replies)
Discussion started by: BG_JrAdmin
2 Replies

2. Solaris

Change the name in SVM

gurus, i have configured the LUN's in solaris 10.after labeled the disk,i have added the disk into one of the soft partition using metattach d0 c5t1000d10s6.actully before that i should confiure the powermt and than i should have add metattch d0 emcpowerc2.i forget to do that and increased... (0 Replies)
Discussion started by: rjay.com
0 Replies

3. Solaris

SVM, mirroring

Really sorry for the long posting. But i would really want to clear all the doubts. I have 2 disk c0t0d0 & c0t1d0, i wanted to mirror c0t1d0 (mirror) to c0t0d0 (main). Creating state database replica: metadb -a -c3 -f c0t0d0s7 ... (3 Replies)
Discussion started by: beginningDBA
3 Replies

4. Solaris

SVM question

I am trying to set up a new server. It has 8 HD's in it. I am using 2 for the system disk. IE set one up mirror to the other. I am using the other 6 as data disks. For those I want to concat 3 together, mirror to the other 3 (also concated together of course) and then make various soft... (7 Replies)
Discussion started by: NewSolarisAdmin
7 Replies

5. UNIX for Dummies Questions & Answers

SVM doubt

i have taken two separate disk A and B created 4 slices in each A b s4 s4 s5 s5 s6 s6 s7 s7 took slices s4 of A and slice s6 0f B ---created a meta device d0 took slices s4 of B and slice s6 0f A---created a meta device d1 created main mirror d2 using d0... (1 Reply)
Discussion started by: vivek_ng
1 Replies

6. Solaris

Problem with SVM

HI, I added by error to a submirror some disks : metattach d53 c2t90d0s0 c2t90d1s0 ... instead of doing a stripe by disk (like that) : metattach d53 c2t90d0s0 metattach d53 c2t90d1s0 .. then, I did a growfs -M to expand FS and the size isn't correct. I tried to launch a... (1 Reply)
Discussion started by: phil.nakache
1 Replies

7. UNIX for Advanced & Expert Users

SVM

How to list out multiple Disk sets in SVM # metaset -s <disksetname> --- This will list out only one diskset but I need a list of disk sets configured for the node. Is there any command,please let me know ... Thanks in advance. (1 Reply)
Discussion started by: pramath
1 Replies

8. UNIX for Advanced & Expert Users

What is interlace value in SVM?

Hi All, I want to know what is the Interlace value in SVM and what is the need of this ? regards, prashant (1 Reply)
Discussion started by: prashant2507198
1 Replies

9. Solaris

SVM Creation

Hello, I recently patched my Solaris 10 box and found out that few of the apps are not working. Fortunately, I had detached the mirroring prior to patching, so I just booted into my secondary disk and found that my apps are working.... The problem is this was way back in last month....see... (14 Replies)
Discussion started by: zigi_p5
14 Replies

10. Solaris

Fsck with SVM

Hello I want to ask that how to mount and run fsck in SVM disk.In my scenario if i have to disks c0t0d0 and c0t1d0 these two disks are in Mirroring (raid1) if i want to run fsck on the disks than below are the right steps? ok boot cdrom -s mount /dev/dsk/c0t0d0s0 /a cd /a fsck... (3 Replies)
Discussion started by: jhonnybravo
3 Replies
mdlogd(1M)						  System Administration Commands						mdlogd(1M)

NAME
mdlogd - Solaris Volume Manager daemon SYNOPSIS
mdlogd DESCRIPTION
mdlogd implements a simple daemon that watches the system console looking for messages written by the Solaris Volume Manger. When a Solaris Volume Manager message is detected, mdlogd sends a generic SNMP trap. To enable traps, you must configure mdlogd into the SNMP framework. See . USAGE
mdlogd implements the following SNMP MIB: SOLARIS-VOLUME-MGR-MIB DEFINITIONS ::= BEGIN IMPORTS enterprises FROM RFC1155-SMI DisplayString FROM SNMPv2-TC; -- Sun Private MIB for Solaris Volume Manager sun OBJECT IDENTIFIER ::= { enterprises 42 } sunSVM OBJECT IDENTIFIER ::= { sun 104 } -- this is actually just the string from /dev/log that -- matches the md: regular expressions. -- This is an interim SNMP trap generator to provide -- information until a more complete version is available. -- this definition is a formalization of the old -- Solaris DiskSuite mdlogd trap mib. svmOldTrapString OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "This is the matched string that was obtained from /dev/log." ::= { sunSVM 1 } -- SVM Compatibility ( error trap ) svmNotice TrapTRAP-TYPE ENTERPRISE sunSVM VARIABLES { svmOldTrapString } DESCRIPTION "SVM error log trap for NOTICE. This matches 'NOTICE: md:'" ::= 1 svmWarningTrap TRAP-TYPE ENTERPRISE sunSVM VARIABLES { svmOldTrapString } DESCRIPTION "SVM error log trap for WARNING.. This matches 'WARNING: md:'" ::= 2 svmPanicTrap TRAP-TYPE ENTERPRISE sunSVM VARIABLES { svmOldTrapString } DESCRIPTION "SVM error log traps for PANIC.. This matches 'PANIC: md:'" ::= 3 END ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWlvma, SUNWlvmr | +-----------------------------+-----------------------------+ |Interface Stability |Obsolete | +-----------------------------+-----------------------------+ SEE ALSO
snmpdx(1M), attributes(5) SunOS 5.11 3 Jun 2004 mdlogd(1M)
All times are GMT -4. The time now is 10:55 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy