I have a multipath system with 2 physicals, a virtual and a failsafe. All network connectivity is working fine to and from all of the interfaces and the virtual. The one thing that is not working is 'ping -s'. From this machine, I cannot send and receive packets using ping -s. ping without the... (1 Reply)
Hi.
I just installed the HP-UX 11i V2.
I have problems with CDE - it is inoperative (after logon there is a message box: messaging system failure - or something like that, it asks to check /etc/hosts and network settings).
nslookup works by hostname and IP, hostname shown the correct... (7 Replies)
Hi All,
My current setup is:
1x Windows Server (Windows 2000 server)
1x Unix Server
2x Windows machine
3x Unix Terminals (Hostnames = A, B and C)
Problem
The problem iam having is Unix terminal C cannot be ping across by Unix terminal A or B or Unix server by using the hostname. Unix... (1 Reply)
I recently installed Solaris 10 on my Sun workstation. I cannot ping using hostname from another computer on the same network.
But I can ping using the IP address. Also I can ping other systems using their hostnames.
Can anyone give some information regarding how to resolve this issue. (4 Replies)
Hello everyone
I have a partition with a problem with ping.
If I do a ping by ip for example ping 1.1.1.1 I got no problem but If I ping by hostname for example ping partition1 take almost a minute to respond me.
I have Aix 5.3 and I have another 19 partitions with no problem. The only... (5 Replies)
hi guys
I got something I haven't been able to fix
I configure a Linux Suse 10 box, added static IP, DNS (resolv), gateway (routes) but I am not able to ping other servers by name but nslookup works and the server can navigate on internet
check below
the problematic server is server-host20
... (4 Replies)
hi....
i have sun solaris 10 server, fedora 10, and Windows Server.. i cant ping my sun solaris 10, fedora 10 and Windows Server using hostname (etc: ping winserver.bengkel2.com), but i can ping all using IPV4 and IPV6 address.. can u give some suggestion to solve my problem or some idea to... (3 Replies)
Hi
We have some 300 servers in the Data center and some of them are running with AIX and some of them are running with Solaris.
I need a script which can be run in one of the server and that script should ping the hostname of all the 300 servers.
Also the script should notify if any server is... (9 Replies)
Hi Team
we have created a DNS server at RHEL6.2 environment in 10.20.203.x/24 network.
Everything is going well on linux client as nslookup, ping by host etc in entire subnet. We are getting problem in windows client as nslookup working as well but not ping. all the firewall is disabled and... (5 Replies)
I have vmware on my windows PC ( hostname : acer ).
vmware has RHEL 7 ( hostname : rhel7 ) installed recently.
RHEL IP configuration
IP : 192.168.5.128
Netmask : 255.255.255.0
ssh to rhel7 works from acer using putty
resolve.conf
cat /etc/resolv.conf
nameserver 192.168.5.1
host... (12 Replies)
Discussion started by: hiten.r.chauhan
12 Replies
LEARN ABOUT DEBIAN
rds-ping
RDS-PING(1) BSD General Commands Manual RDS-PING(1)NAME
rds-ping -- test reachability of remote node over RDS
SYNOPSIS
rds-ping [-c count] [-i interval] [-I local_addr] remote_addr
DESCRIPTION
rds-ping is used to test whether a remote node is reachable over RDS. Its interface is designed to operate pretty much the standard ping(8)
utility, even though the way it works is pretty different.
rds-ping opens several RDS sockets and sends packets to port 0 on the indicated host. This is a special port number to which no socket is
bound; instead, the kernel processes incoming packets and responds to them.
OPTIONS
The following options are available for use on the command line:
-c count
Causes rds-ping to exit after sending (and receiving) the specified number of packets.
-I address
By default, rds-ping will pick the local source address for the RDS socket based on routing information for the destination address
(i.e. if packets to the given destination would be routed through interface ib0, then it will use the IP address of ib0 as source
address). Using the -I option, you can override this choice.
-i timeout
By default, rds-ping will wait for one second between sending packets. Use this option to specified a different interval. The timeout
value is given in seconds, and can be a floating point number. Optionally, append msec or usec to specify a timeout in milliseconds
or microseconds, respectively.
Specifying a timeout considerably smaller than the packet round-trip time will produce unexpected results.
AUTHORS
rds-ping was written by Olaf Kirch <olaf.kirch@oracle.com>.
SEE ALSO rds(7), rds-info(1), rds-stress(1).
BSD Apr 22, 2008 BSD