SPHINTERPOLATE(1gmt)					       Generic Mapping Tools					      SPHINTERPOLATE(1gmt)

NAME

       sphinterpolate - Gridding in tension of spherical data

SYNOPSIS

       sphinterpolate	infiles   -Ggrdfile   [   -F   ]   [  -H[i][nrec]  ]  [  -Ixinc[unit][=|+][/yinc[unit][=|+]]  ]  [  -Qmode[/options]  ]  [
       -Rwest/east/south/north[r] ] [ -V ] [ -Z ] [ -:[i|o] ] [ -b[i|o][s|S|d|D[ncol]|c[var1/...]] ][ -m[i|o][flag] ]

DESCRIPTION

       sphinterpolate reads one or more ASCII [or binary] files (or standard input) containing lon, lat, f and performs a  Delaunay  triangulation
       to  set up a spherical interpolation in tension.  The final grid is saved to the specified file.  Several options may be used to affect the
       outcome, such as choosing local versus global gradient estimation or optimize the tension selection to satisfy one of four criteria.

       infiles
	      Data files with the (lon, lat, f) coordinates in ASCII (or binary; see -b).  If no files are given the standard input is read.

       -G     Name of the output grid to hold the interpolation.

OPTIONS

       -F     Force pixel node registration [Default is gridline registration].  (Node registrations are defined in GMT  Cookbook  Appendix  B	on
	      grid file formats.)

       -H     Input  file(s)  has  header  record(s).  If used, the default number of header records is N_HEADER_RECS.	Use -Hi if only input data
	      should have header records [Default will write out header records if the input data have them]. Blank lines and lines starting  with
	      # are always skipped.

       -I     x_inc  [and optionally y_inc] is the grid spacing. Optionally, append a suffix modifier.	Geographical (degrees) coordinates: Append
	      m to indicate arc minutes or c to indicate arc seconds.  If one of the units e, k, i, or n is appended  instead,	the  increment	is
	      assumed  to be given in meter, km, miles, or nautical miles, respectively, and will be converted to the equivalent degrees longitude
	      at the middle latitude of the region (the conversion depends on ELLIPSOID).  If /y_inc is given but set to 0 it will be reset  equal
	      to x_inc; otherwise it will be converted to degrees latitude.  All coordinates: If = is appended then the corresponding max x (east)
	      or y (north) may be slightly adjusted to fit exactly the given increment [by default the increment may be adjusted slightly  to  fit
	      the  given  domain].  Finally, instead of giving an increment you may specify the number of nodes desired by appending + to the sup-
	      plied integer argument; the increment is then recalculated from the number of nodes and the domain.  The resulting  increment  value
	      depends on whether you have selected a gridline-registered or pixel-registered grid; see Appendix B for details.	Note: if -Rgrdfile
	      is used then grid spacing has already been initialized; use -I to override the values.

       -Q     Specify one of four ways to calculate tension factors to preserve local shape properties or satisfy arc constraints [Default  is	no
	      tension].

       -Q0    Piecewise linear interpolation; no tension is applied.

       -QQ1   Smooth interpolation with local gradient estimates.

       -QQ2   Smooth  interpolation with global gradient estimates.  You may optionally append /N/M/U, where N is the number of iterations used to
	      converge at solutions for gradients when variable tensions are selected (e.g., -T only) [3], M is the number of Gauss-Seidel  itera-
	      tions used when determining the global gradients [10], and U is the maximum change in a gradient at the last iteration [0.01].

       -QQ3   Smoothing.   Optionally append /E/U [/0/0], where E is Expected squared error in a typical (scaled) data value, and U is Upper bound
	      on  weighted sum of squares of deviations from data.

       -R     west,  east,  south,  and  north	specify  the  Region  of  interest,  and  you  may  specify  them  in  decimal	 degrees   or	in
	      [+-]dd:mm[:ss.xxx][W|E|S|N]  format.   Append r if lower left and upper right map coordinates are given instead of w/e/s/n.  The two
	      shorthands -Rg and -Rd stand for global domain (0/360 and -180/+180 in longitude respectively, with -90/+90 in  latitude).  Alterna-
	      tively, specify the name of an existing grid file and the -R settings (and grid spacing, if applicable) are copied from the grid.

       -T     Use variable tension (ignored with -Q0 [constant]

       -V     Selects verbose mode, which will send progress reports to stderr [Default runs "silently"].

       -Z     Before interpolation, scale data by the maximum data range [no scaling].

       -:     Toggles  between (longitude,latitude) and (latitude,longitude) input and/or output.  [Default is (longitude,latitude)].  Append i to
	      select input only or o to select output only.  [Default affects both].

       -bi    Selects binary input.  Append s for single precision [Default is d (double)].  Uppercase S or D will force  byte-swapping.   Option-
	      ally,  append ncol, the number of columns in your binary input file if it exceeds the columns needed by the program.  Or append c if
	      the input file is netCDF. Optionally, append var1/var2/... to specify the variables to be read.  [Default is 3 input columns].

       -bo    Selects binary output.  Append s for single precision [Default is d (double)].  Uppercase S or D will force byte-swapping.   Option-
	      ally, append ncol, the number of desired columns in your binary output file.  [Default is same as input].

       -m     Multiple segment file(s).  Segments are separated by a special record.  For ASCII files the first character must be flag [Default is
	      '>'].  For binary files all fields must be NaN and -b must set the number of output columns explicitly.  By default the  -m  setting
	      applies to both input and output.  Use -mi and -mo to give separate settings to input and output.

ASCII FORMAT PRECISION

       The  ASCII  output formats of numerical data are controlled by parameters in your .gmtdefaults4 file.  Longitude and latitude are formatted
       according to OUTPUT_DEGREE_FORMAT, whereas other values are formatted according to D_FORMAT.  Be aware that the format in effect  can  lead
       to  loss of precision in the output, which can lead to various problems downstream.  If you find the output is not written with enough pre-
       cision, consider switching to binary output (-bo if available) or specify more decimals using the D_FORMAT setting.

GRID VALUES PRECISION

       Regardless of the precision of the input data, GMT programs that create grid files will internally hold the grids in 4-byte floating  point
       arrays.	 This is done to conserve memory and furthermore most if not all real data can be stored using 4-byte floating point values.  Data
       with higher precision (i.e., double precision values) will lose that precision once GMT operates on the grid or writes out new  grids.	To
       limit loss of precision when processing data you should always consider normalizing the data prior to processing.

EXAMPLES

       To interpolate the points in the file testdata.txt on a global 1x1 degree grid with no tension, use

       sphinterpolate testdata.txt -Rg -I1 -Gsolution.grd

SEE ALSO

       GMT(1), greenspline(1) sphdistance(1) sphtriangulate(1) triangulate(1)

REFERENCES

       Renka,  R, J., 1997, Algorithm 772: STRIPACK: Delaunay Triangulation and Voronoi Diagram on the Surface of a Sphere, AMC Trans. Math. Soft-
       ware, 23(3), 416-434.
       Renka, R, J,, 1997, Algorithm 773: SSRFPACK: Interpolation of scattered data on the Surface of a Sphere with a surface under  tension,  AMC
       Trans. Math. Software, 23(3), 435-442.

GMT 4.5.7							    15 Jul 2011 					      SPHINTERPOLATE(1gmt)