Sponsored Content
Full Discussion: How swap used in HPUX ?
Operating Systems HP-UX How swap used in HPUX ? Post 302575295 by vbe on Monday 21st of November 2011 08:37:27 AM
Old 11-21-2011
Swap is to allow a system to run more processes its memory can allow, by removing sleeping processes from memory (RAM) and move them to to virtual memory (disk) this process is called swapping. A well tuned machine should never or rarely swap or just a little.. You have 11 GB of permanent disk access on system disk...
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

HPUX 10.20 et HPUX 11

Is there any problems of binaries compatibility between HPUX 10.20 et 11 ? (2 Replies)
Discussion started by: Olivier
2 Replies

2. UNIX for Dummies Questions & Answers

Swap

When i re-updated my system i set my swap at 500 MB. I have 256 in ram and have never even gone into the 250 mb of swap that i had originally configured. How do I reduce the swap? (3 Replies)
Discussion started by: macdonto
3 Replies

3. UNIX for Dummies Questions & Answers

New to HPUX

Hi, I am a SAP Basis admin recentely been asked to administer a HPUX server. Could someone recommend some good study material to learn with the Sap prespective. -carry (1 Reply)
Discussion started by: carryclare
1 Replies

4. UNIX for Dummies Questions & Answers

About swap

Is it really so that if swap will be located in the begining of hard drive, than it will work faster? (1 Reply)
Discussion started by: Ty3
1 Replies

5. Solaris

Swap config - Mirror swap or not?

Hello and thanks in advance. I have a Sun box with raid 1 on the O/S disks using solaris svm. I want to unmirror my swap partition, and add the slice on the second disk as an additional swap device. This would give me twice as much swap space. I have been warned not to do this by some... (3 Replies)
Discussion started by: BG_JrAdmin
3 Replies

6. Shell Programming and Scripting

Need Script to Use CPUs on a HPUX server to simulate Workload Manager on HPUX.

I am running HPUX and using WLM (workload manager). I want to write a script to fork CPUs to basically take CPUs from other servers to show that the communication is working and CPU licensing is working. Basically, I want to build a script that will use up CPU on a server. Any ideas? (2 Replies)
Discussion started by: cpolikowsky
2 Replies

7. Red Hat

swap not defined as swap

free -m : 1023 total swap space created default partition /dev/sdb1 50M using fdisk. i did write the changes. #mkswap /dev/sdb1 #swapon /dev/sdb1 free -m : 1078 total swap space this shows that the swap is on Question : i did not change the type LINUX SWAP (82) in fdisk. so why is... (5 Replies)
Discussion started by: dplinux
5 Replies

8. HP-UX

Swap device file and swap sapce

Hi I have an integrity machine rx7620 and rx8640 running hp-ux 11.31. I'm planning to fine tune the system: - I would like to know when does the memory swap space spill over to the device swap space? - And how much % of memory swap utilization should be specified (swap space device... (6 Replies)
Discussion started by: lamoul
6 Replies

9. HP-UX

pwage-hpux-T for Trusted HPUX servers

I'm sharing this in case anybody needs it. Modified from the original solaris pwage script. This modified hpux script will check /etc/password file on hpux trusted systems search /tcb and grep the required u_succhg field. Calculate days to expiry and notify users via email. original solaris... (2 Replies)
Discussion started by: sparcguy
2 Replies

10. Solaris

Explain the output of swap -s and swap -l

Hi Solaris Folks :), I need to calculate the swap usage on solaris server, please let me understand the output of below swap -s and swap -l commands. $swap -s total: 1774912k bytes allocated + 240616k reserved = 2015528k used, 14542512k available $swap -l swapfile dev swaplo... (6 Replies)
Discussion started by: seenuvasan1985
6 Replies
SYSTEMD-MACHINE-ID-COMMIT.SERVICE(8)			 systemd-machine-id-commit.service		      SYSTEMD-MACHINE-ID-COMMIT.SERVICE(8)

NAME
systemd-machine-id-commit.service - Commit a transient machine ID to disk SYNOPSIS
systemd-machine-id-commit.service DESCRIPTION
systemd-machine-id-commit.service is an early boot service responsible for committing transient /etc/machine-id files to a writable disk file system. See machine-id(5) for more information about machine IDs. This service is started after local-fs.target in case /etc/machine-id is a mount point of its own (usually from a memory file system such as "tmpfs") and /etc is writable. The service will invoke systemd-machine-id-setup --commit, which writes the current transient machine ID to disk and unmount the /etc/machine-id file in a race-free manner to ensure that file is always valid and accessible for other processes. See systemd-machine-id-setup(1) for details. The main use case of this service are systems where /etc/machine-id is read-only and initially not initialized. In this case, the system manager will generate a transient machine ID file on a memory file system, and mount it over /etc/machine-id, during the early boot phase. This service is then invoked in a later boot phase, as soon as /etc has been remounted writable and the ID may thus be committed to disk to make it permanent. SEE ALSO
systemd(1), systemd-machine-id-setup(1), machine-id(5), systemd-firstboot(1) systemd 237 SYSTEMD-MACHINE-ID-COMMIT.SERVICE(8)
All times are GMT -4. The time now is 03:56 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy