Did cfgmgr complain when being run? Did that DLPAR-action ie. assigning the controller with the attached tape drive to the LPAR show any complaints either?
Can you identify the SCSI controller with the tape drive using lsdev? Is lsdev showing any other type of tape drive but rmt that can be brought into relation to the SCSI controller (that you might have identified)?
You can only assign it, if it is on a separate SCSI controller which is not assigned to other LPARs. But if that was not the case, I assumed the HMC might have complained about it.
hi all ,
i have just installed solris 9 on a sun 280R ,and i have appleid the recommended patches .
after the installation i have found that /dev/rmt/ directory is empty , i thought that was normal , so i attached my DDS4 external tape drive and treid :
devfsadm -C
devfsadm -v
reboot --... (1 Reply)
Hi.
After the shutdown for SWIFT Alliance Server, tape backup process will be done. Unfortunately, I encountered this error message when I performed the database tape backup. The error was "/dev/rmt 0.1 block size is 0; variable; must be 1024 fixed. Consider reconfiguration through 'chdev'... (2 Replies)
Hi Guys,
I a newbie in Unix environment. I need a help to detect my external SCSI tape drive. I tried with command drvconfig;devlinks;tapes.. but when I go to /dev/rmt/, the directory is still empty.
I also tried with add_drv -v st but I'm getting this message
# add_drv -v st
exit... (8 Replies)
Hi all,
Sometimes, when I reboot my AIX server, my tape drive /dev/rmt# assignments change. This creates some tedious TSM work prior to and after a reboot of the server.
Is there a way to ensure that the /dev/rmt# assignments come up the same every time?
Thanks (5 Replies)
Hi folks,
I am trying to learn Unix based in Linux...
In Linux, in /Dev are files related to cards, mouse, etc..
how about Unix?
What is the difference between /Dev and /Devices?
Thanks,
Fernanda (0 Replies)
I have an HP Proliant DL380 with Intel Processors that I recently loaded Solaris 10 with latest patches on it. I'm trying to do a ufsdump to an HP DAT 40 tape drive via SCSI, but I can't get it to do anything because /dev/rmt is empty. I've tried the following with luck:
touch /reconfigure,... (7 Replies)
Hi,
In our HP-UX B.11.11. I could not find dev/urandom and dev/random
Are all pseudo-devices implemented as device drivers, or in need to run /configure some package to install the package to have dev/urandom.
Please help (4 Replies)
Discussion started by: rashi
4 Replies
LEARN ABOUT OSF1
tms
tms(7) Miscellaneous Information Manual tms(7)NAME
tms - TMSCP magnetic tape interface
SYNOPSIS
For XMI/KDM on Alpha-based systems:
bus xmi0 at iop0 vector xmierror
controller uq0 at xmi? port kdm vector uqintr
device tape tms0 at uq0 drive 0
For MSI Bus: only MIPS-based DECsystem 5500
bus msi0 at ibus? vector msi_isr
controller dssc1 at msi0 msinode 1
device tape tms3 at dssc1 drive 3
For XMI/CI/HSC on Alpha-based systems:
bus xmi0 at iop0 vector xmierror
bus ci0 at xmi? port np vector cimna_isr
controller hsc6 at ci0 cinode 6
device tape tms3 at hsc6 drive 3
For tms devices dual ported between two controllers:
device tape tms2 at * drive 2
DESCRIPTION
The TMSCP driver provides a standard tape drive interface, as described in mtio(7). This is a driver for any controller that adheres to
the Tape Mass Storage Control Protocol (TMSCP). The TMSCP controllers communicate with the host through a packet-oriented protocol termed
the Tape Mass Storage Control Protocol.
Tape Support - Alpha-based systems
TA78, TA79, TA81, TA90, TA90E, TA91
Diagnostics
All diagnostic messages are sent to the error logger subsystem.
FILES
/dev/rmt???
/dev/nrmt???
SEE ALSO mtio(7), MAKEDEV(8), uerf(8), tapex(8) delim off
tms(7)