Thanks for replies .. my problem is resolved ...
for my curiousness am asking one more question... like is there any command with terminates the sleep mode of a job.. ... is there any way to set the sleep out timings .. i means the script should sleep only for 3 hours .. if it goes beyond 3 hours it should come out of the script.
i will give u more detail
the script will sleep untill the messag becomes "P"... it may take one hour or 5 hours ... so my thing is while defining the sleep timing is there any way to give sleep time out after 3 hours .? is there any command like sleep out.
please let me know if there is such command.
Thanks
Sree
Last edited by Franklin52; 10-27-2011 at 09:07 AM..
Reason: Please use code tags, thank you
I am running a number of processes through a kill -15 loop as a temporary fix to some viscious memory leaks. I cannot pass the entire list of processes through the kill at once, because the nature of the monitoring my client has will cause the software to failover.
Because of the large number of... (1 Reply)
I am in need of some help; think I have confused myself.
Here is the issue I am faced with.
The script log file was fine, the nohup.out file has tens of thousands of lines like illegal use of sleep: sleep seconds
So I assume there is something with the seconds calculation in the script... (1 Reply)
Hi All I have a requiremnt to run a script inside another script.
here i am pulling the record count from the table in oracle.If record count is greater than 0 the script is executed.The scripts updates the count in the table and again the count is found out and the condition is checked and same... (3 Replies)
Hi Forum
Im using sleep in a while loop goes around 10 times. i feed it a variable with the time i what it to sleep for eg sleep $sleepVal and then print system date and time to screen but sometimes 1 second is added to the time why is this
here my code
sleepVal=5
while
do
... (3 Replies)
Hello,
Need a little help with the script below. I can't get it to sleep :( I'm trying to get this to check if the process is running and if it is, wait 10 secs and check again. Keep doing this until it's not running and then stop checking and send the email.
#!/bin/ksh
mailto=`cat... (2 Replies)
Hi Frnz,
I need to execute sleep command but i dont know the definite time.
Let me put my req:
I am running one shell script and this script creates some lock file in temp dir ...now in my script i want one function to go into sleep mode till this lock file exists..one lock file gone that... (6 Replies)
I need help in script.
I want my one script execute every time at 6:30 am and i have no cron access.
So i am putting sleep command there , Script may took half an hour 35 min , it depend upon queries how much it take time, but that is not issue,
So i want according to stop time of... (15 Replies)
Discussion started by: pallvi_mahajan
15 Replies
LEARN ABOUT OSX
sleep
SLEEP(1) BSD General Commands Manual SLEEP(1)NAME
sleep -- suspend execution for an interval of time
SYNOPSIS
sleep seconds
DESCRIPTION
The sleep command suspends execution for a minimum of seconds.
If the sleep command receives a signal, it takes the standard action.
IMPLEMENTATION NOTES
The SIGALRM signal is not handled specially by this implementation.
The sleep command will accept and honor a non-integer number of specified seconds (with a '.' character as a decimal point). This is a non-
portable extension, and its use will nearly guarantee that a shell script will not execute properly on another system.
EXIT STATUS
The sleep utility exits 0 on success, and >0 if an error occurs.
EXAMPLES
To schedule the execution of a command for x number seconds later (with csh(1)):
(sleep 1800; sh command_file >& errors)&
This incantation would wait a half hour before running the script command_file. (See the at(1) utility.)
To reiteratively run a command (with the csh(1)):
while (1)
if (! -r zzz.rawdata) then
sleep 300
else
foreach i (`ls *.rawdata`)
sleep 70
awk -f collapse_data $i >> results
end
break
endif
end
The scenario for a script such as this might be: a program currently running is taking longer than expected to process a series of files, and
it would be nice to have another program start processing the files created by the first program as soon as it is finished (when zzz.rawdata
is created). The script checks every five minutes for the file zzz.rawdata, when the file is found, then another portion processing is done
courteously by sleeping for 70 seconds in between each awk job.
SEE ALSO nanosleep(2), sleep(3)STANDARDS
The sleep command is expected to be IEEE Std 1003.2 (``POSIX.2'') compatible.
HISTORY
A sleep command appeared in Version 4 AT&T UNIX.
BSD April 18, 1994 BSD