10-26-2011
ok, so for all the above commands to work correctly for both Solaris 10 and 8, I need to be root?
i tried sudo but got denied...i guess i need to raise a request to get that level of access...
well if this is the problem, thanks for the help, i'll keep trying after i get sudo access.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I have worked with Qlogic (Sun) fiber cards a lot and with Emulex fiber cards only a little. Here is the scenario: I have a Sun 490 with 3 Emulex cards in it. A pair are for the 6120 array that is attached, the other is a direct attach so our SAN for Veritas Netbackup to back up the system.I... (0 Replies)
Discussion started by: lm_admin_dh
0 Replies
2. UNIX for Advanced & Expert Users
Hi,
I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine.
The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards.
Can anyone suggest how to determine my HBA hardware ?
Thanks,
Ron.
... (3 Replies)
Discussion started by: ronbarak
3 Replies
3. Solaris
Hi,
I'm trying to determine which HBA cards are installed on my Solaris 10 (Sun-Fire-V240) machine.
The relevant data I have is below, but from it I cannot ascertain for sure if I have Emulex 10000 or 11000 HBA cards.
Can anyone suggest how to determine my HBA hardware ?
Thanks,
Ron.
... (4 Replies)
Discussion started by: ronbarak
4 Replies
4. Solaris
Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies
5. Solaris
I have installed a qlogic HBA card in an E450 Solaris 9 with all the SUNW packages and the latest EPROM version. Configuration reboot was done. An orange light flashes to the right of where the card plugs into the fiber cable after booting, and the following error apprears at the start of the boot... (9 Replies)
Discussion started by: floydm
9 Replies
6. UNIX for Advanced & Expert Users
I have a V490 that has couple internal disks attached to the same dual-port HBA card that I'm planning attach to the SAN for additional storage.
Would I sacrifice performance if I use the same HBA?
Is it better to throw in a new HBA instead? (1 Reply)
Discussion started by: kiem
1 Replies
7. AIX
Hi All,
SUN emulex HBA card has been installed on P520 box.
When i run the cfgmgr i am getting the following message.
lpar2#cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies
8. Solaris
Hi,
i have a two port hba card in solaris 10 system one of which is disabled. How to enable and configure the other port.
---------- Post updated at 08:17 AM ---------- Previous update was at 03:40 AM ----------
please help :( (7 Replies)
Discussion started by: rishiraaz
7 Replies
9. Solaris
I have JNI FCE-6460-N fc card , it is detected in OK prompt.....I connected Sun StorEDGE A5000 FC storage.
in OK prompt, PROBE-SCSI-ALL
showing A5000 fc hdds details in ok prompt.....
but in OS level.....not showing the hdd, i tried in DEVFSADM command and FORMAT command not showing A5000... (3 Replies)
Discussion started by: anysystem
3 Replies
10. Red Hat
Hi,
How to determine if HBA card in getting faulty from linux host ? any pointers. (2 Replies)
Discussion started by: saurabh84g
2 Replies