[Solved] Help with running ps -e | less on nano script editor
p { margin-bottom: 0.08in; } This is just a portion of a script I'm writing on Linux nano script editor. When I run the script I get stuck on the ps -e | less command portion of the script. It displays all the process running but it does not allow me to move to the next line on the script. when it gets to the end of the display all I get is [END] I hit enter but it has no effect. Is there an option I must use?
Thank you
Code:
if [ "$answer" = "yes" ]
then
ps -e | less
echo -e "\n\nWhich process would you like to terminate?:\c"
read PID
exit 0
else
display
fi
done
Last edited by Franklin52; 10-22-2011 at 10:55 AM..
Reason: Please use code tags for data and code samples, thank you
All,
I am running one perl script from prompt and its running fine, but while putting it on cron gives below error,
DB-Library error:
Could not open interface file. (2 Replies)
What I want my script to do is to run a command in Terminal and close that same Terminal window when the process is complete.
Of course I could ad a delay of 6 seconds to complete the process, but it may not be enough every time.
To simplify my question, this is what I want to achieve.... (9 Replies)
p { margin-bottom: 0.08in; } As you can already tell I am a newbie. I took a Microsoft VB2008 a few month back. Now I'm taking Linux + and this course requires me to write scripts. The script executes but, I can't figure out or have not found anything that I can make out on the internet that can... (4 Replies)
Good afternoon!
I have a script in cron that runs every ten minutes. Normally it only takes a minute or so to complete. However there are times when the amount of data it is looking at is large, and it has taken 20 minutes.
So I want for it to look for the script before it starts.
I was... (8 Replies)
Hi freinds,
I have tried running a script through cron ,it is a shell script which calls a oracle procedure , problem here is that there is function in sql code which makes a external C call , this function is failing when running manually but works when run manually.
I have trouble shooted... (6 Replies)
i have script A and script B, both scripts have to run in parallel, my requirement is script A create table temp1, post creating it will run fr 4 hrs , script B has to start 0nly after creation of table temp1 ( which is done by script A) , again script B will run for 5 hrs
if i run sequencially... (7 Replies)
Hello.
This is my situation.
script .anything
ls -l .
---How can I see the content of .anything using (i.e) cat .anything?
If not possible can someone suggest a sequence to simulate a console-recorder
to "observ" from a RUNNING script session?
Thanks
Paolo
Please use code tags... (3 Replies)
Hi,
I do have an R script named KO.R. Basically reads thousands of files, whose name has a pattern that differs at a portion of the file name, List.txt.
Row_file1_mile.txt
Row_file2_mile.txt
Row_file3_mile.txt
...
...
Row_file1000_mile.txt
Below is a portion of my Rscript that reads... (4 Replies)
Hi,
Whenever i try to open a file in any editor like vi, vim and nano i get this help.txt showing up in split screen without any key being pressed. This continues to pop up even when i close the help.txt. This behavior happens only when i am connected via putty. Is there a fix to this issue?
... (1 Reply)
Discussion started by: sunil0391
1 Replies
LEARN ABOUT DEBIAN
nano-tiny
NANO-TINY(1) General Commands Manual NANO-TINY(1)NAME
nano-tiny - Nano's ANOther editor, an enhanced free Pico Clone
SYNOPSIS
nano-tiny [options] [+LINE] file
DESCRIPTION
This manual page documents briefly the nano-tiny command.
nano is a small, free and friendly editor which aims to replace Pico, the default editor included in the non-free Pine package. Rather than
just copying Pico's look and feel, nano also implements some missing (or disabled by default) features in Pico, such as "search and
replace" and "goto line number".
nano-tiny is a special, minimal build of the program, aimed for Debian's boot-floppies or emergency disks.
OPTIONS -V (--version)
Show the current version number and author.
-h (--help)
Display a summary of command line options.
See the nano(1) manpage for the complete documentation of nano.
BUGS
Please send any comments or bug reports to
nano@nano-editor.org.
The nano mailing list is available from
nano-devel@lists.sourceforge.net. To subscribe, email to nano-devel-request@lists.sourceforge.net with a subject of "subscribe".
HOMEPAGE
http://www.nano-editor.org/
AUTHOR
Chris Allegretta <chrisa@asty.org>, et al (see AUTHORS for details). This manual page was originally written by Jordi Mallach <jordi@sin-
dominio.net>, for the Debian system (but may be used by others).
February 20, 2002 NANO-TINY(1)
10-22-2011
. It displays all the process running but it does not allow me to move to the next line on the script. when it gets to the end of the display all I get is [END] I hit enter but it has no effect. Is there an option I must use?