I am running a number of processes through a kill -15 loop as a temporary fix to some viscious memory leaks. I cannot pass the entire list of processes through the kill at once, because the nature of the monitoring my client has will cause the software to failover.
Because of the large number of... (1 Reply)
I am in need of some help; think I have confused myself.
Here is the issue I am faced with.
The script log file was fine, the nohup.out file has tens of thousands of lines like illegal use of sleep: sleep seconds
So I assume there is something with the seconds calculation in the script... (1 Reply)
Hi All I have a requiremnt to run a script inside another script.
here i am pulling the record count from the table in oracle.If record count is greater than 0 the script is executed.The scripts updates the count in the table and again the count is found out and the condition is checked and same... (3 Replies)
Hi Forum
Im using sleep in a while loop goes around 10 times. i feed it a variable with the time i what it to sleep for eg sleep $sleepVal and then print system date and time to screen but sometimes 1 second is added to the time why is this
here my code
sleepVal=5
while
do
... (3 Replies)
Hello,
Need a little help with the script below. I can't get it to sleep :( I'm trying to get this to check if the process is running and if it is, wait 10 secs and check again. Keep doing this until it's not running and then stop checking and send the email.
#!/bin/ksh
mailto=`cat... (2 Replies)
Hi Frnz,
I need to execute sleep command but i dont know the definite time.
Let me put my req:
I am running one shell script and this script creates some lock file in temp dir ...now in my script i want one function to go into sleep mode till this lock file exists..one lock file gone that... (6 Replies)
I need help in script.
I want my one script execute every time at 6:30 am and i have no cron access.
So i am putting sleep command there , Script may took half an hour 35 min , it depend upon queries how much it take time, but that is not issue,
So i want according to stop time of... (15 Replies)
Discussion started by: pallvi_mahajan
15 Replies
LEARN ABOUT OPENSOLARIS
scsi_setup_cdb
scsi_setup_cdb(9F) Kernel Functions for Drivers scsi_setup_cdb(9F)NAME
scsi_setup_cdb - setup SCSI command descriptor block (CDB)
SYNOPSIS
int scsi_setup_cdb(union scsi_cdb *cdbp, uchar_t cmd, uint_t addr,
uint_t cnt, uint_t othr_cdb_data);
INTERFACE LEVEL
Solaris DDI specific (Solaris DDI).
PARAMETERS
cdbp Pointer to command descriptor block.
cmd The first byte of the SCSI group 0, 1, 2, 4, or 5 CDB.
addr Pointer to the location of the data.
cnt Data transfer length in units defined by the SCSI device type. For sequential devices cnt is the number of bytes. For
block devices, cnt is the number of blocks.
othr_cdb_data Additional CDB data.
DESCRIPTION
The scsi_setup_cdb() function initializes a group 0, 1, 2, 4, or 5 type of command descriptor block pointed to by cdbp using cmd, addr,
cnt, othr_cdb_data.
addr should be set to 0 for commands having no addressing information (for example, group 0 READ command for sequential access devices).
othr_cdb_data should be additional CDB data for Group 4 commands; otherwise, it should be set to 0.
The scsi_setup_cdb() function does not set the LUN bits in CDB[1] as the makecom(9F) functions do. Also, the fixed bit for sequential
access device commands is not set.
RETURN VALUES
The scsi_setup_cdb() function returns:
1 Upon success.
0 Upon failure.
CONTEXT
These functions can be called from a user, interrupt, or kernel context.
SEE ALSO makecom(9F), scsi_pkt(9S)
Writing Device Drivers
American National Standard Small Computer System Interface-2 (SCSI-2)
American National Standard SCSI-3 Primary Commands (SPC)
SunOS 5.11 16 Jan 2006 scsi_setup_cdb(9F)