Ethtool script not running on boot. Post: 302566657

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Running a program on boot!

Hi there! I tried to search for something like this here but couldn't find anything. I need to run a specific program when linux starts up. I need to run it after the rp-pppoe has started because this prog needs internet connection. I start the program by entering ./dynix start (its in my home...

2. Filesystems, Disks and Memory

Compile a code for running on boot

How can I compile a code that can be runned on boot:??

3. Ubuntu

system not booting after running local boot scripts

I have two systems in my computer . I update the ubuntu system these days and always interrupt it and exit the system . now the system cannot boot after Running local boot scripts(/etc/rc.local), it just stops there. i have to terminate the gnome display manager. what can i do with it ? thank...

4. Solaris

Running from Shell Vs running from RC script

Hi, i have a script which need to do behave differently when run as a startup process from init.d/ rc2.d script and when run manually from shell. How do i distinguish whether my script is run by init process or by shell?? Will the command /proc/$$/psinfo | grep "myscript" work well???...

5. Shell Programming and Scripting

ethtool : command not found

Hi, I am uising Suse linux on my system and i tried : man ethtool and i got the manual for ethtool but when i tried to use the command as: ethtool -a eth0 it says Command not found. also, i tried rpm -qa|grep ethtool i got: ethtool-3-15.2 so,it means my system has ethtool server or...

6. Programming

ethtool problem

Hi, I'm using ethtool to change network settings: Just for the experiment, i want to change speed to 10, instead of 100, I type: ethtool -s eth0 speed 10 duplex full autoneg off and to view settings i type: ethtool eth0, and get this: Settings for eth0: Supported ports: ...

7. UNIX for Dummies Questions & Answers

check service is running at boot

dears am having solaris 10, and i would like to know if the NTP service is running when the OS staritng?on the other hand how can i make it start at the boot up?note the ntp is managed by the SMF in solaris 10. thanks a lot

8. Shell Programming and Scripting

Script will keep checking running status of another script and also restart called script at night

I am using blow script :-- #!/bin/bash FIND=$(ps -elf | grep "snmp_trap.sh" | grep -v grep) #check snmp_trap.sh is running or not if then # echo "process found" exit 0; else echo "process not found" exec /home/Ketan_r /snmp_trap.sh 2>&1 & disown -h ...

9. Red Hat

Can't boot RHEL7.2 due to "Start Job is Running"

Dear community, as already done tons of times, I prepare the RedHat installation on VMWare, then clone it with clonezilla, and finally restore it on final server. Due to different hrdware, I have to boot from rhel-server-7.4-x86_64-boot.iso cd and rewrite the initramfs that contains the hardware...

10. UNIX for Beginners Questions & Answers

Ethtool command not working

Hi All, I am trying to find my NIC card speed in centos 5. But i am unable to get the info using ethtool command. # ethtool eth0 Settings for eth0: Link detected: yes and even tried to look for the file # cd /sys/class/net/eth0/speed files which is also not available....

LEARN ABOUT XFREE86

malo

MALO(4) 						   BSD Kernel Interfaces Manual 						   MALO(4)

NAME

     malo -- Marvell Libertas IEEE 802.11b/g wireless network driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   device malo
	   device pci
	   device wlan
	   device firmware

     Alternatively, to load the driver as a module at boot time, place the following lines in loader.conf(5):

	   if_malo_load="YES"

DESCRIPTION

     The malo driver provides support for Marvell Libertas 88W8335 based PCI and Cardbus network adapters.  malo supports station and monitor mode
     operation.  Only one virtual interface may be configured at any time.  For more information on configuring this device, see ifconfig(8).

     This driver requires the malofw firmware kernel module be installed before it will work.  The firmware files are not publicly available.  A
     port of the firmware can be found at:

	   http://weongyo.org/project/malo/malo-firmware-1.4.tar.gz

     The firmware kernel module can be installed by extracting the archive and running 'make install clean' in the malo-firmware-1.4 directory.

HARDWARE

     The following cards are among those supported by the malo driver:

	   Card 		  Chip	     Bus	Standard
	   Netgear WG311v3	  88W8335    PCI	b/g
	   Tenda TWL542P	  88W8335    PCI	b/g
	   U-Khan UW-2054i	  88W8335    PCI	b/g

EXAMPLES

     Join an existing BSS network (i.e., connect to an access point):

	   ifconfig wlan create wlandev malo0 inet 192.168.0.20 
	       netmask 0xffffff00

     Join a specific BSS network with network name ``my_net'':

	   ifconfig wlan create wlandev malo0 ssid my_net up

     Join a specific BSS network with 64-bit WEP encryption:

	   ifconfig wlan create wlandev malo0 ssid my_net 
		   wepmode on wepkey 0x1234567890 weptxkey 1 up

SEE ALSO

     cardbus(4), pci(4), wlan(4), wlan_ccmp(4), wlan_tkip(4), wlan_wep(4), ifconfig(8), wpa_supplicant(8)

HISTORY

     The malo device driver first appeared in FreeBSD 7.1.

BSD
								 October 21, 2009							       BSD

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Running a program on boot!

Discussion started by: D-Lexy

2. Filesystems, Disks and Memory

Compile a code for running on boot

Discussion started by: d4n1l0d

3. Ubuntu

system not booting after running local boot scripts

Discussion started by: tcb3210

4. Solaris

Running from Shell Vs running from RC script

Discussion started by: vickylife