Changed disk controller -> drops into GRUB?! Post: 302566615

9 More Discussions You Might Find Interesting

1. Solaris

Controller target disk?

Hi, I am a newbie to Solaris. I want to know how to find out the controller target and disk number on a SunFire V890 box that has 6X72GB disks. The probe-scsi output is as shown below: /pci@8,600000/SUNW,qlc@2 LiD HA LUN --- Port WWN --- ----- Disk description ----- 0 0 0 ...

2. SCO

Warning HD: no root disk controller was found

hi... i hav a problem to install sco unix while installing sco unix 5.0.5 in acer altos with hardware raid am getting error "Warning HD: no root disk controller was found system error 5: while getting fs type flushing controller: DAC960PRL cache done." i hav use the following...

3. HP-UX

[Joy Share] - Replace an unknown status controller on HP FC60 disk array

Replace an unknown status controller on HP FC60 disk array Author:JoyOnline JoyChangLu@gmail.com Trouble description: The users detected that the status of controller at A is unknown. Analysis and diagnostic: Physical observed all leds on enclosure of disk array is normal. The...

4. SCO

SCO 5.0.7 no root disk controller found error during install

I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd. I have a raid 5 array with an online spare created using 4 36.3 GB...

5. Solaris

Help needed to find out the disk controller for veritas disks

hi all i am using vxvm 5.1 on my sun blade 150 which is running with solaris 5.10. When i give the command "vxdisk list" it gives the following output # vxdisk list DEVICE TYPE DISK GROUP STATUS c0t0d0s2 auto:none - - online...

6. SCO

Change Disk controller in SCO 6.0.0

So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller. First, I downloaded the megasas driver from SCO and installed it on the old system. Then I created a new Microlite Edge emergency boot cd with the new driver on it. I...

7. Solaris

Changed to AHCI, can not access disk???

Here is my problem: I have an 1.5TB disk with OpenSolaris (b134, b151a) using non AHCI. I then changed to AHCI in BIOS, which results in severe problems: I can not boot the system. I suspect the problem is because I changed to AHCI. Now I have changed back to non AHCI, but still I can not...

8. Solaris

Disk controller reassignment

Hi The scenario in the oracle t4-1 hardware with solaris 10 is as follows: 1. The initial install on the server was performed with an incorrect disk layout. 2. New disks were ordered and slot into the server. 3. The disks are allocated a controller and a disk number based on the disk or...

9. Linux

Grub not loading from replaced disk

Hi, a little while ago, one of the GPT Partitioned hard disk had gone faulty in a Mirror RAID and is now successfully replaced. here is how I did that. 1) created identical partition table on the new disk. 2) attached the mirrors using md commands. The whole procedure is given below:...

LEARN ABOUT LINUX

grub-install

GRUB-INSTALL(8) 					  System Administration Utilities					   GRUB-INSTALL(8)

NAME

       grub-install - install GRUB to a device

SYNOPSIS

       grub-install [OPTION] install_device

DESCRIPTION

       Install GRUB on your drive.

       -h, --help
	      print this message and exit

       -v, --version
	      print the version information and exit

       --modules=MODULES
	      pre-load specified modules MODULES

       --boot-directory=DIR
	      install GRUB images under the directory DIR/grub instead of the /boot/grub directory

       --grub-setup=FILE
	      use FILE as grub-setup

       --grub-mkimage=FILE
	      use FILE as grub-mkimage

       --grub-mkrelpath=FILE
	      use FILE as grub-mkrelpath

       --grub-mkdevicemap=FILE use FILE as grub-mkdevicemap

       --grub-probe=FILE
	      use FILE as grub-probe

       --no-floppy
	      do not probe any floppy drive

       --allow-floppy
	      Make the drive also bootable as floppy (default for fdX devices). May break on some BIOSes.

       --recheck
	      probe a device map even if it already exists

       --force
	      install even if problems are detected

       --disk-module=MODULE
	      disk module to use

       INSTALL_DEVICE can be a GRUB device name or a system device filename.

       grub-install copies GRUB images into /boot/grub, and uses grub-setup to install grub into the boot sector.

REPORTING BUGS

       Report bugs to <bug-grub@gnu.org>.

SEE ALSO

       grub-mkconfig(8), grub-mkimage(1), grub-setup(8), grub-mkrescue(1)

       The full documentation for grub-install is maintained as a Texinfo manual.  If the info and grub-install programs are properly installed at
       your site, the command

	      info grub-install

       should give you access to the complete manual.

grub-install (GRUB) 1.99-12ubuntu5				   October 2011 						   GRUB-INSTALL(8)