10-19-2011
in case of a power outage you will lose any data in cache which isn't (yet) written to disks... a new battery would be the safer way!
10 More Discussions You Might Find Interesting
1. Solaris
I have a Sun Sparc T2000 (Solaris 10 05-08) and have installed a PCI-X 4GB Single Port HBA card in it.
I have one StorageTek 2540 array that I would like to connect to the T2000.
For the moment it would be a single path connection, but I've ordered a 2nd HBA, so eventually it would be... (4 Replies)
Discussion started by: soliberus
4 Replies
2. Solaris
We're moving our production 3510FC to development, so we need to replace the production 3510FC. The 6140 is nice, but pricey.
Here's the question: Would two 2540's (RAID 10) be 'faster' than one 3510? (RAID 10) and faster than one 6140 (RAID 10)?
One StoregeTek 6140 (16x72GB 15k rpm fc-al... (12 Replies)
Discussion started by: buddhavelvet
12 Replies
3. Filesystems, Disks and Memory
Hi,
We have 12x1TB SATA disks in our array and I need to create 10TB volume. I defined new storage profile on array and when I tried to add volume, I faced with ~2TB limit for new volumes. I didn't find how to set another limit on my storage profile. Is there is a way to configure one large... (3 Replies)
Discussion started by: Sapfeer
3 Replies
4. Solaris
Hi,
I have a simple question on how to correctly disable the matrix?
Looking for the Common Array Manager and I do not see this option...
Thank for help (3 Replies)
Discussion started by: bieszczaders
3 Replies
5. Solaris
Hi peeps,
Was wondering if anyone can help me, got a couple of storagetek 2540's that I need to configure. Trouble is I think they were brought as second user as all that came with them was cables.
Does anyone know how to configure them (i.e. create raid sets and map to Luns and present... (1 Reply)
Discussion started by: callmebob
1 Replies
6. Hardware
Hello all !
I am a beginner about system and networking , and after some research on internet , i didn't find any relevant information , so i post here , if someone have an experience with this kind of material or if some documentation about how to connect my storage device on my server.
I... (2 Replies)
Discussion started by: acorradi
2 Replies
7. Solaris
Can someone point me to a procedure detailing the replacement of a failed battery in a SUN 6540 controller.
Or describe the procedure.
Thanks (1 Reply)
Discussion started by: USFE
1 Replies
8. Hardware
Hi Guys and Gals,
Wionder if you could help me, got a problem with a controller on a storagetek 2540, dead when fully powered up but if you reboot, it is ok for a couple of seconds (and you can ping it). Then once the array is fully up, it goes faulty and is un-pingable.
Had anyone... (4 Replies)
Discussion started by: callmebob
4 Replies
9. Solaris
Bought a Sun StorageTek 2540 SAN array a few years ago from a company that was going out of business. When we first set it up, we were able to get all the software (Common Array Manager) and firmware directly from Sun.
We just upgraded the drives, but the array is too large for the firmware. Now... (6 Replies)
Discussion started by: edison303
6 Replies
10. Solaris
Hi Guys,
I have situation here ...
server M4000 server lost connectivity to storagetek 2540
, storagetek 2540 unable to be ping.From DAS URL the storage is undetected.
Any idea why this is happening. Please share.
Thank you.
Raj (1 Reply)
Discussion started by: muralirajah
1 Replies
LEARN ABOUT OPENSOLARIS
acpi
ACPI(1) General Commands Manual ACPI(1)
NAME
acpi - Shows battery status and other ACPI information
SYNOPSIS
acpi [options]
DESCRIPTION
acpi Shows information from the /proc or the /sys filesystem, such as battery status or thermal information.
OPTIONS
-b | --battery
show battery information
-a | --ac-adapter
show ac adapter information
-t | --thermal
show thermal information
-c | --cooling
show cooling device information
-V | --everything
show every device, overrides above options
-s | --show-empty
show non-operational devices
-i | --details
show additional details if available:
* battery capacity information
* temperature trip points
-f | --fahrenheit
use fahrenheit as the temperature unit instead of default celsius
-k | --kelvin
use kelvin as the temperature unit instead of default celsius
-p | --proc
use the old /proc interface, default is the new /sys one
-d | --directory <dir>
path to ACPI info (either /proc/acpi or /sys/class)
-h | --help
display help and exit
-v | --version
output version information and exit
AUTHOR
The original version of this manual page was written by Paul Telford <pxt@debian.org> for the Debian system. Newer additions were done by
Michael Meskes <meskes@debian.org>. Permission is granted to copy, distribute and/or modify this document under the terms of the GNU GPL.
ACPI(1)