10-13-2011
booting in "diag" mode or removing the rsc card should redirect the output to the ttya port on the server. are you sure, you've the right cable for a serial connection? if i remember right, you'll need a "null modem" cable to connect to the 25pin port...
(the "diag" mode statement is only true with firmware higher than 4.15.x; removing of rsc card should always work)
9 More Discussions You Might Find Interesting
1. AIX
I'm stuck - when I boot the machine and hit 5 on the keyboard, all I get is an SP login. Can someone give me some tips on how to get to the install via the serial port? (2 Replies)
Discussion started by: tb0ne
2 Replies
2. HP-UX
I have a HP Visualize C200 running hpux that I am trying to boot into using a null modem through com1 from my Sun Ultra 10. I get all the way to the login prompt and then it becomes innactive and wont let me access the machine anymore. Any ideas? (2 Replies)
Discussion started by: trajek
2 Replies
3. Solaris
Hi
I have a stupid problem with ultra 5 console connection.
I can't connect to serial port with my laptop.
I made these configurations from ok prompt:
OK setenv input-device ttya
OK setenv output-device ttya
OK setenv auto-boot? false
I tried to connect to machine with cisco rollover... (5 Replies)
Discussion started by: noizer`
5 Replies
4. OS X (Apple)
I'm trying to use an old Commodore 128D as a terminal to access OS X's shell via a serial port. I've used 'screen' and 'zterm' to ensure the two machines are successfully interfaced.
Instructions for opening up the serial console on other Unix-y operating systems don't work with OS X Leopard. ... (3 Replies)
Discussion started by: joecassara
3 Replies
5. Solaris
Hello Folks,
I am having trouble to login to rsc or serial console of V890.
The rsc2.2.3 has been configured with required parameters, resetrs and even rebooted. When serial port is connected to laptop, The hyper terminal does not get the console or POSt messages when the server is rebooting... (8 Replies)
Discussion started by: defflepord
8 Replies
6. Solaris
Hi. I am very very new to Solaris. I found an abandoned Sun Blade 150. I created a 3-wire null modem cable, connected it to an abandoned laptop and successfully installed Solaris 10 using the serial port. This laptop doesn't have ethernet. So I want to establish a PPP connection.
Part of the... (2 Replies)
Discussion started by: neutronscott
2 Replies
7. UNIX for Dummies Questions & Answers
Hi Gurus,
Can some one explain me the difference between a IP console and a serial console. (1 Reply)
Discussion started by: rama krishna
1 Replies
8. Solaris
i am running solaris 10 in my vmware workstation. How to setup a console for my solaris box. in Vmware i could see a serial port option. can some one help me on how i can setup a console . (0 Replies)
Discussion started by: chidori
0 Replies
9. Solaris
Hi Experts.
i have been stuck up with an issue.
i have connected my Solaris 8 , Sun fire V445 on serial port by using Teraterm.
Initially i was able to login and executed some tasks.
After executing some commands (mainly Control +c), i am not able to type any key or not able to do anything at... (2 Replies)
Discussion started by: siddulamadhu
2 Replies
LEARN ABOUT DEBIAN
via-diag
VIA-DIAG(8) System Manager's Manual VIA-DIAG(8)
NAME
via-diag - EEPROM setup and diagnostic program for the VIA Rhine vt86c100 and vt3043 Ethernet controller chips.
SYNOPSIS
via-diag [options]
DESCRIPTION
via-diag is a program that you can use to diagnose problems with VIA Rhine vt86c100 and vt3043 Ethernet controller chips.
OPTIONS
These programs follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is
included below.
-h, --help
Show summary of options.
-V, --version
Show version of program.
-v, --verbose
Verbose mode.
-q, --quiet
Be very unverbose.
-# <cardnum>
Use card number <cardnum>.
-a, --show_all_registers
Print all registers.
-e, --show-eeprom
Dump EEPROM contents to stdout.
-E, --emergency-rewrite
Re-write a corrupted EEPROM.
-p, --base-address <port>
Specify port to use.
-A, --Advertise <mediaype>
Advertise media type. Valid Options are: 10baseT, 100baseT4, 100baseTx, 100baseTx-FD, 100baseTx-HD, 10baseT-FD and 10baseHD.
-F, --new-interface <interface>
Interface number. Options that make sense are: 10baseT, 10base2, AUI, 100baseTx, 10baseT-FDX, 100baseTx-FDX, 100baseT4, 100baseFx,
100baseFx-FDX, MII, HomePNA and Autosense.
-H, --new-hwaddress <address>
Set card to a new hardware address.
-m, --show-mii
Dump MII management registers.
-R, --reset
Reset the transceiver.
-T, --test
Do register and SRAM test.
-w, --write-EEPROM <values>
Write to the EEPROMS with the specified values. Do not use this, if you do not know what you do!
-f, --force-detection
Try to identify the card, even if it is active.
-t, --chip-type <card>
Explicitly set the chip. To get all valid numbers, run via-diag with the options '-t -1'.
SEE ALSO
mii-diag(8)
AUTHOR
via-diag was written and is still maintained by Donald Becker <becker@scyld.com>. This manual page was written by Alain Schroeder
<alain@debian.org>, for the Debian GNU/Linux system (but may be used by others).
February 18, 2002 VIA-DIAG(8)