Hy all,
i've a little problem with the size of the swap. I've an old solaris machine, with 4Go, and swap is taking 500Mo for only 1% used at any time.
So : how can i change this size without problems ?????
(ok it may be a stupid question, but it's a real problem when you lose about 1 or 2... (3 Replies)
Hello all,
I just got a laptop with redhat linux 7.2 installed, but during the installation the installer only put 1gig of sawp space( this laptop has 1gig of RAM). To my understanding when creating swap space, the size is determine by double the RAM. Therefore my question is that how do I... (2 Replies)
I have a machine: SunOS <server> 5.9 Generic_117171-15 sun4u sparc SUNW,Sun-Fire-480R
It has these filesystems:
Filesystem size used avail capacity Mounted on
/dev/md/dsk/d0 19G 15G 3.9G 80% /
/proc 0K 0K 0K 0% /proc... (6 Replies)
few questions
a. where can I find the RAM of a server? im about to install redhat on a server (reformat). need to know because it will be my basis for swap size. i saw something line 3048MB detected upon boot. is this the memory?
b. what is the command in lunux to check the original size of... (2 Replies)
Dear All,
How to increase the swap size when physicall memory reaches 60 %. OR it can be only done after the physicall memory is full.
Rgds
Rj (8 Replies)
Hi All,
I want to know how to understand the actual swap size.
My o/p shows as below
root@ecovs1a # swap -s
total: 4546056k bytes allocated + 358856k reserved = 4904912k used, 5046688k available
root@ecovs1a # swap -l
swapfile dev swaplo blocks free
/dev/md/dsk/d31 ... (9 Replies)
Hi Experts,
Need your advise in determining the size of swap space in of the new HP-Ux server.
Server is having 32G of physical memory.
Ideally what amout of physical memory should be allocated as a swap space?
Following document from HP suggests to have minimum swap space... (2 Replies)
Hi,
the /tmp size is less whereas the size allocated to swap is quite big. how to increase the size of /tmp -
#: swap -l
swapfile dev swaplo blocks free
/dev/md/dsk/d20 85,20 8 273096 273096
#: swap -s
total: 46875128k bytes allocated + 2347188k reserved =... (2 Replies)
Discussion started by: psb74
2 Replies
LEARN ABOUT OSX
locale::codes::langvar
Locale::Codes::LangVar(3pm) Perl Programmers Reference Guide Locale::Codes::LangVar(3pm)NAME
Locale::Codes::LangVar - standard codes for language variation identification
SYNOPSIS
use Locale::Codes::LangVar;
$lvar = code2langvar('acm'); # $lvar gets 'Mesopotamian Arabic'
$code = langvar2code('Mesopotamian Arabic'); # $code gets 'acm'
@codes = all_langvar_codes();
@names = all_langvar_names();
DESCRIPTION
The "Locale::Codes::LangVar" module provides access to standard codes used for identifying language variations, such as those as defined in
the IANA language registry.
Most of the routines take an optional additional argument which specifies the code set to use. If not specified, the default IANA language
registry codes will be used.
SUPPORTED CODE SETS
There are several different code sets you can use for identifying language variations. A code set may be specified using either a name, or
a constant that is automatically exported by this module.
For example, the two are equivalent:
$lvar = code2langvar('en','alpha-2');
$lvar = code2langvar('en',LOCALE_CODE_ALPHA_2);
The codesets currently supported are:
alpha
This is the set of alphanumeric codes from the IANA language registry, such as 'arevela' for Eastern Armenian.
This code set is identified with the symbol "LOCALE_LANGVAR_ALPHA".
This is the default code set.
ROUTINES
code2langvar ( CODE [,CODESET] )
langvar2code ( NAME [,CODESET] )
langvar_code2code ( CODE ,CODESET ,CODESET2 )
all_langvar_codes ( [CODESET] )
all_langvar_names ( [CODESET] )
Locale::Codes::LangVar::rename_langvar ( CODE ,NEW_NAME [,CODESET] )
Locale::Codes::LangVar::add_langvar ( CODE ,NAME [,CODESET] )
Locale::Codes::LangVar::delete_langvar ( CODE [,CODESET] )
Locale::Codes::LangVar::add_langvar_alias ( NAME ,NEW_NAME )
Locale::Codes::LangVar::delete_langvar_alias ( NAME )
Locale::Codes::LangVar::rename_langvar_code ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangVar::add_langvar_code_alias ( CODE ,NEW_CODE [,CODESET] )
Locale::Codes::LangVar::delete_langvar_code_alias ( CODE [,CODESET] )
These routines are all documented in the Locale::Codes::API man page.
SEE ALSO
Locale::Codes
The Locale-Codes distribution.
Locale::Codes::API
The list of functions supported by this module.
http://www.iana.org/assignments/language-subtag-registry
The IANA language subtag registry.
AUTHOR
See Locale::Codes for full author history.
Currently maintained by Sullivan Beck (sbeck@cpan.org).
COPYRIGHT
Copyright (c) 2011-2012 Sullivan Beck
This module is free software; you can redistribute it and/or modify it under the same terms as Perl itself.
perl v5.16.2 2012-10-11 Locale::Codes::LangVar(3pm)