Hi Gurus,
I am working in tcsh and i set the prompt with this.
set prompt = "$cwd>"
But I see teh prompt only gets reflected with the directory where I set the prompt. After i cd to another directory it still shows the old directory. Please advise (1 Reply)
Hi All,
I have Solaris-10 machine. Yesterday I patched it with Solaris-10 patch Cluster. Since then glance software is filling up /var/core continuously. In every few minutes, it will fill /var to 100%.
Glance runs through /etc/init.d/mwa and I already stopped it, still core files are... (15 Replies)
Hey Guys,
I have been searching but unable to find solution for this;
Got 2 files:
#File A
A
B
C
#File B
1
2
3
And would like to 'merge' file and get a out put like;
A1
A2
A3
B1 (2 Replies)
Hi there,
I'm working on a Suse 8 based system and picked up that the crontab was missing. after some investigation i realized that the hole /var directory is missing. :mad:
I would like to now if its common for this directory to go missing?
Can I copy another Suse 8 /var directory to this... (10 Replies)
Hi,
I am receiving an email to the server with a html attachment. When I check the /var/mail the attachment is showing as junk characters.
I want to move that html file to a particular location in that server.
Please help me.
Regards
Neethu (4 Replies)
Hi Guys,
I am facing this Error
bash-2.03$ ./curl -V
ld.so.1: curl: fatal: libldap.so.5: open failed: No such file or directory
Killed
bash-2.03$
while executing
./curl -V in /opt/sfw/bin directory.
I am using Sun Solaris 10.
which package upgrage can give me this missing... (9 Replies)
Hi All,
I'm having problem with /var directory which is keep increasing. Here's the output of bdf and du command
# uname -a
HP-UX rppmis1 B.11.11 U 9000/800 1153414645 unlimited-user license
# bdf /var
Filesystem kbytes used avail %used Mounted on
/dev/vg00/lvol8 ... (8 Replies)
Hi All,
Can any one help me here.I'm getting whole files name of the directory along with the grep result.
below is the code
var=`grep -i '127.3.3.1' _record`
echo $var (9 Replies)
Hi,
I am facing issue with one of the drive is solaris 10. it is showing offline in the messages file
scsi: WARNING: /pci@2,600000/QLGC,qlc@0/fp@0,0/ssd@w5006016746e00b1b,0 (ssd0):
drive offline
genunix: WARNING: Page83 data not standards compliant DGC LUNZ 0430
... (1 Reply)
Discussion started by: Prasanth T K
1 Replies
LEARN ABOUT LINUX
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)