Hey,
Just need a little help I'm not sure wat I should do.
We have several little networks setup for testing different things. One of these networks we need to have running at full dulpex.
Right now we run 2 hubs (to go off to 2 differnt parts) and they are half dulpex hubs.
Is is... (1 Reply)
I have setup a AS 2.1 server with no X running or installed. I need to know how to configure the IP and such from command line and change it from DHCP. We used DHCP at first since we didn't know the IP we were going to use and now I need to change it. Any help would be great as Redhat's site just... (2 Replies)
I have a machine that has developed a strange network problem. Anytime it sends an FTP file somewherwe, no problem. When it is the target machine, extremely slow. I checked the /var/adm/messages file and found a few of these:
SUNW,hme0 : No response from Ethernet network : Link down -- cable... (2 Replies)
This is my first attempt in installing a netbsd ever. I'm trying to get myself familiar with some commands and how things work in unix and so far i never knew its this fun. Anyway, unix is our elective here in school and school is gonna start 2 weeks. I'm just trying to get a headstart on this :D... (2 Replies)
1) how do i know my NIC speed if its 10//100???
2)how do i setup by NIC to full duplex
3) any help on setting up etherchannel for NIC failover (1 Reply)
I am new to Solaris and have been searching around for this answer and I think I figured it out but I wanted to run it by you folks. I was trying to figure out if the network on this Solaris 10 machine was set up for 100 Full Duplex. I think from this output that it is 100 full duplex, am I... (2 Replies)
Hi,
I have a linux machine connected to 2 networks, with devices eth0 and eth1.
When I give the command host whatever, how do I now which network is searched for the DNS's ? Is there a default ethernet device for network related commands ? How do I change it ? :confused: (2 Replies)
Hi here is my question;
any help would be appreciated
The Linux system pokey has two Ethernet cards. The first Ethernet card is connected to a companywide
TCP/IP network covering the addresses 87.65.43.xx, where pokey's address is
87.65.43.21. The second Ethernet interface is connected to a... (2 Replies)
Folks;
I have 2 SUSE servers similar in all configuration & both on the same network
(192.168.151.10 & 192.168.151.11) with the same default gateway of 192.168.151.1 and the same netmask of 255.255.255.0 and the same firewall configuration
the first one works fine and i can ssh to it & i can... (3 Replies)
Hi,
I am on Redhat 5. on the /etc/sysconfig/network file
I don't see GATEWAY as one line. I also checked /etc/sysconfig/network-scripts/ifcfg-eth0. I don't see GATEWAY.
But on the server. But when I do netstat -rn. I see many address. Is there some other settings ?
... (2 Replies)
Discussion started by: samnyc
2 Replies
LEARN ABOUT DEBIAN
pbuilder-uml.conf
pbuilder-uml.conf(5) pbuilder pbuilder-uml.conf(5)NAME
pbuilder-uml.conf - configuration file for user-mode-linux port of pbuilder
DESCRIPTION
/etc/pbuilder/pbuilder-uml.conf contains default values used in pbuilder-user-mode-linux program invocation.
FORMAT
MY_ETH0=tuntap,,,192.168.0.2
Configures ethernet setting used for booting linux. See how rootstrap boots your system, and copy that.
Specify --eth0=slirp,12345,/usr/bin/slirp-fullbolt to use the slirp connection.
UML_IP=192.168.0.3
IP address to use for guest OS.
This can be set to dhcp for obtaining IP address through DHCP.
UML_NETMASK=255.255.255.0
Guest OS netmask
UML_NETWORK=192.168.0.0
Guest OS network
UML_BROADCAST=255.255.255.255
Guest OS broadcast
UML_GATEWAY=192.168.0.1
Guest OS gateway
PBUILDER_UML_IMAGE=${HOME}/uml-image
Guest OS file system image.
UML_MOUNT_TMPFS=no
Whether to mount tmpfs inside the guest image. This is probably mostly useless.
BUILDPLACE=${HOME}/tmp/
The location which build will take place. pbuilder-user-mode-linux will place temporary COW files to there. The user running UML
needs to be able to access that directory.
UML_MEM=128
The amount of memory allowed for UML. Give more value to here.
UML_HOSTNAME=uml-host
The hostname for the UML.
The hostname should be available in /etc/hosts so that hostname -f will be able to return the FQDN.
UML_BUILDRESULT=/directory/of/build/result
The directory where build result of pbuilder-user-mode-linux is stored.
ROOTSTRAP_IMAGESIZE=size-in-megabytes
The size, in MB, of the disk iamge to create. Defaults to 1000.
NOTES
It is advised to set APTCACHEHARDLINK to no in ~/.pbuilderrc. see pbuilderrc(5) for details.
AUTHOR
Initial coding, and main maintenance is done by Junichi Uekawa <dancer@debian.org>.
The homepage is available at http://pbuilder.alioth.debian.org
FILES
/etc/pbuilder/pbuilder-uml.conf, ${HOME}/.pbuilderrc
SEE ALSO
/usr/share/doc/pbuilder/pbuilder-doc.html, pbuilder-user-mode-linux(1), pbuilder(8), pbuilderrc(5), pdebuild(1)Debian 2003 Jan 8 pbuilder-uml.conf(5)
10-11-2011
