10-09-2011
First of all, SCO UNIX OpenServer is not Linux. I would be very surprised if the existing SCO Adaptec Ultra32 driver worked with a newer board such as the UL50 Dual Channel VHDCI Ultra320 SCSI PCIe card.
Off the wall but maybe you should consider a PCI-X to PCIe adoptor and continue to use your existing SCSI card.
10 More Discussions You Might Find Interesting
1. Solaris
How do I get the PCI ID for my Realtek adapter?
It's a Solaris x86 installation. (5 Replies)
Discussion started by: kuultak
5 Replies
2. Solaris
Has anyone ever relocated an HBA card after already having it configured in another PCI slot? I've found that the HBA instance #'s start incrementing past the previous. It results in me having to have my instance numbers in /kernel/drv/qla2300.conf be 4,5,6,7 instead of 0,1,2,3. Cleanup with... (5 Replies)
Discussion started by: kduffin
5 Replies
3. AIX
I have 1 PCI-X Dual Channel Ultra320 SCSI Adapter card for my p570 server. I would like to split the 2 channels for the usage of 2 tape drives in different LPARs. Is that possible?
For example, I have 2 LPARs running in p570 server, LPAR-A configured the Ultra320 card as pci7 in slot... (11 Replies)
Discussion started by: kwliew999
11 Replies
4. SCO
I'm floundering here trying to locate a PCI-E 1x HBA that will support an external tape drive in SCO Openserver 6. I was unable to find anything that would work in the compatible hardware list and a call to Adaptec confirmed that PCI-X would've been a better option for the risers in the Dell 2950... (1 Reply)
Discussion started by: s_mal
1 Replies
5. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
6. SCO
OK group, it's been 12 years since I worked with SCO. I need some direction here:
SCO Openserver 5.07
I have a server with a bad motherboard. I have moved the SCSI adapter and hard drive to another computer. This new server has different hardware so I must install the chipset drivers for... (1 Reply)
Discussion started by: jscholz
1 Replies
7. Hardware
Internally speaking, for your motherboard bus. Would it be possible for a usb standard to be used in place of the PCI or PCIe bus that is now nearly standard on all PC's? If not, why wouldn't this work? (8 Replies)
Discussion started by: Lost in Cyberia
8 Replies
8. Red Hat
I am trying to cause a callback in the Linux nvme driver by using AER injection. I've modified the AER source code to directly inject errors through module loading rather than from userland program.
I've verified that I got the correct bus, dev, and fn and that the error injection went... (0 Replies)
Discussion started by: Decrypto
0 Replies
9. HP-UX
I am trying to reload a RP4440 with 2x300gb disks and dual Port Network card, with HPUX 11.11 Sept 2003. When the os boots and and gets to the main menu to install HPUX or run recovery, it cannot find the disks or NIC.
At the OS prompt (after loading files), ioscan shows the Class ba, and shows... (0 Replies)
Discussion started by: mrmurdock
0 Replies
10. Solaris
Hi,
I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error:
WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1):
SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies
AHA(4) BSD Kernel Interfaces Manual AHA(4)
NAME
aha -- Adaptec SCSI host adapter driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device aha
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
aha_load="YES"
In /boot/device.hints:
hint.aha.0.at="isa"
DESCRIPTION
This driver provides access to the SCSI bus connected to the Adaptec AHA-154x and AHA-1640 SCSI host adapters. x is 0 for controllers with-
out a floppy drive and 2 for controllers that have them. For optimum performance, Adaptec AHA-174x controllers should be configured in
enhanced mode and attached via the ahb(4) driver.
One device hint entry for every card to be attached by the system is required. Specific values for the port address, IRQ, and DRQ may be
specified. If wildcard values are used, the driver will query the device for its current settings and use those. If the port address is a
wildcard, the driver consults an internal table of possible port address locations and attaches to the first unattached card it finds. The
possible port addresses for this card are 0x330, 0x334, 0x230, 0x234, 0x130, and 0x134.
The AHA-1640 is an MCA bus card. Since the MCA bus is a self-identifying bus, no setting of hints is required.
HARDWARE
The aha driver supports the following SCSI host adapters:
o Adaptec AHA-154xB
o Adaptec AHA-154xC
o Adaptec AHA-154xCF
o Adaptec AHA-154xCP
o Adaptec AHA-1640
o Adaptec AHA-174x in 154x emulation mode
o DTC 3290 SCSI controller in 1542 emulation mode
o Tekram SCSI controllers in 154x emulation mode
SEE ALSO
ahb(4), ahc(4), aic(4), cd(4), da(4), sa(4), scsi(4)
AUTHORS
The aha driver was ported by M. Warner Losh from the bt driver written by Justin T. Gibbs.
BUGS
The AHA-154xA card does not support residuals on data transfers. As a result, this card is no longer supported.
There have been some reports that the AHA-154xB does not work well under heavy load.
The AHA-154xCP is a plug and play controller. However, its resources are set using the on-board BIOS and cannot be moved. Failures to
attached for this card are often caused when the resources set in the BIOS conflict.
BSD
July 4, 2004 BSD