Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Solaris 10 + mpxio Path
Operating Systems Solaris Solaris 10 + mpxio Path Post 302562681 by general_lee on Friday 7th of October 2011 04:33:53 PM
Old 10-07-2011
Yep, triple checked cables. When I was at the data centre.

I'm not sure about the array being active/active. The RAID GROUPS are assigned to a specific array controller (CM0 or CM1 in my case), I can manually assign the RAID GROUP to either CM0 or CM1 which changes the "Access State" for the paths.

However, I'm not convinced this will automatically fail over if a controleer or HBA fails. I'll look at the array in greater detail.

Let me know if you have any more ideas.

Thanks,
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

path name for Solaris 8 ?

hello all, instead of type pwd everytime to find down where I am at. is there a command set prompt to put in to your profile on shell so it invisible every you type cd? thanks in advance... (3 Replies)
Discussion started by: phapvn
3 Replies

2. Solaris

Mpxio

Hi All, I have one question. I found out that my system setting for mpxio-disable=yes. Sun recommend to change it to mpxio-disable=no and run stmsboot -e command. But no one can tell will it affect the system or not and the system is sol-10 and using veritas volume manager and attached... (3 Replies)
Discussion started by: mailbox80
3 Replies

3. Solaris

Mpxio

Hi, I have a quick question. How can I see MPXIO statistics (like errors, how many I/O|throuput per path, ....) on Solaris 10? Does maybe a ready dtrace script exist (I do not have the knowledge to write one myself)? I would be happy if somebody knows some good documentation/links (with... (1 Reply)
Discussion started by: victorinox
1 Replies

4. Filesystems, Disks and Memory

VxVM and MPxIO

:confused: Last week I read that VxVM won't work with MPxIO (i don't recall the link) and that it should be unconfigured when installing VxVM. Today I read that VxVM works in "pass-thru" mode with MPxIO and DMP uses the devices presented by MPxIO. If I create disks with MPxIO and use VxVM to... (1 Reply)
Discussion started by: bluescreen
1 Replies

5. Filesystems, Disks and Memory

MPxIO question

Greetings Forumers!! I was given a T2000 with one, dual port, HBA card. The card had one fiber connection to the SAN and the former admin enabled MPxIO. Yesterday, I learned that the other port was connected to the same SAN. This system is in another city so I don't have physical access to... (1 Reply)
Discussion started by: bluescreen
1 Replies

6. Solaris

Solaris 10 - QLogic 4060C iSCSI adapter - multipathed (MPxIO)

System: Sun M3000 and M4000 OS: Solaris 10 (fully up to date with latest patches) iSCSI HBA: 2x QLE4060C (QLogic) In each system are 2 QLE4060C iSCSI adapters. I manage to set up both HBA's to connect to the LUNs on the SAN However I don't manage to enable multi-pathing. Made the... (4 Replies)
Discussion started by: sb008
4 Replies

7. Solaris

MPXIO

Hi Kudo, I wanna to know that how can I do mpxio device name to os native name mapping without using stmsboot -L I tried everything still not able to got the solution till I able to get these o/p here is native disk info as well physical wat is the logical OS name of the disk ... (1 Reply)
Discussion started by: tarunn.dubeyy
1 Replies

8. Solaris

Solaris 10 MPXIO doesn't recover path failure

I have been running some tests with solaris mpxio, dual-pathed to HDS SAN storage. When I take a path offline, Solaris recognised this and a path is shown as offline in luxadm display <device>. However, it does not recover on reinstatement of the path until I run cfgadm -al. Any ideas? Phil (3 Replies)
Discussion started by: UKPhil
3 Replies

9. Solaris

solaris turn off multipath mpxio

Im not able to turn the multipath off on the solaris s10 X86...since im on FC boot.. if i disable multipath , from /kernel/drv/iscsi.conf then im not able to boot the machine.:wall: Is there any other go or any suggestions . (2 Replies)
Discussion started by: gowtham.varma
2 Replies

10. Solaris

Reset MPxIO total path count

We recently moved our netapp disks onto new infrastructure by attaching the new controllers to our fibre switch and netapp migrating the disks. Disks kept the same address. We originally had 4 paths, but after attaching the new controllers we had 8. Now I want to remove the old paths. But can't. ... (5 Replies)
Discussion started by: garydeena
5 Replies

LEARN ABOUT DEBIAN

raidfile.conf

RAIDFILE.CONF(5)						    Box Backup							  RAIDFILE.CONF(5)

NAME

       raidfile.conf - Userland RAID for Box Backup

SYNOPSIS

       /etc/box/raidfile.conf

DESCRIPTION

       The raidfile.conf is usually generated by raidfile-config(8) but may be manually edited if the store locations move or if more than one
       disc set is required.

       discX
	   Specifies a set of discs.

	   SetNumber
	       The set number of the RAID disc, referenced by each account.

	   BlockSize
	       The block size of the file system (usually 2048). Under BSD with FFS, set this to your file system's fragment size (most likely an
	       8th of the block size).

	   Dir0
	       The first directory in the RAID array.

	   Dir1
	       The second directory in the RAID array. If you do not wish to use the built-in RAID functionality, this field should be set to the
	       same as Dir0. You should not use the built-in RAID if you have a hardware RAID solution or if you're using another type of software
	       RAID (like md on Linux).

	   Dir2
	       The third directory in the RAID array. The same notes that apply to Dir2 also apply to Dir3.

FILES

       /etc/box/raidfile.conf

SEE ALSO

       raidfile-config(8), bbstored.conf(5)

AUTHORS

       Ben Summers

       Per Thomsen

       James O'Gorman

Box Backup 0.11 						    10/28/2011							  RAIDFILE.CONF(5)
All times are GMT -4. The time now is 10:04 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy