Sponsored Content
Full Discussion: Sun cluster
Operating Systems Solaris Sun cluster Post 302562493 by h@foorsa.biz on Friday 7th of October 2011 05:27:38 AM
Old 10-07-2011
As DukeNuke2 said Sun Cluster is for 64 machines . for videos have a look here
 

9 More Discussions You Might Find Interesting

1. High Performance Computing

SUN Cluster Vs Veritas Cluster

Dear All, Can anyone explain about Pros and Cons of SUN and Veritas Cluster ? Any comparison chart is highly appreciated. Regards, RAA (4 Replies)
Discussion started by: RAA
4 Replies

2. Solaris

sun cluster

hi can u please send me how to configure cluster in x86 machines. i am using VM ware. Is there any difference in X86 and SPARC cluster installations please help me thaks to all (1 Reply)
Discussion started by: sijocg
1 Replies

3. Solaris

Sun Cluster 3.2

Hi, I am getting these messages constantly at random times there is not visible impact but would like to know what these messages mean? Cluster.RGM.rgmd: resource group on node change to RG_ON_PENDING_R_RERT Cluster.RGM.rgmd: resource group on node change to RG_ONLINE (1 Reply)
Discussion started by: xor
1 Replies

4. Solaris

Sun Cluster

Hi All I hav working knowledge on solarois 10. Could anyone suggest me any doc or material for learning SUN cluster from scratch. Anything from basic level . Thanks in advance!! (1 Reply)
Discussion started by: ningy
1 Replies

5. Solaris

Sun cluster and Veritas cluster question.

Yesterday my customer told me to expect a vcs upgrade to happen in the future. He also plans to stop using HDS and move to EMC. Am thinking how to migrate to sun cluster setup instead. My plan as follows leave the existing vcs intact as a fallback plan. Then install and build suncluster on... (5 Replies)
Discussion started by: sparcguy
5 Replies

6. Solaris

Sun cluster 3.2

Hi I have a new mount point which is to added to to an existing resource group. I read many docs but I am not able to find the exact methods. Could anyone help me pls. (1 Reply)
Discussion started by: ningy
1 Replies

7. Solaris

Sun cluster 3.1

Hi, I have upgraded a Sparc T2000 server which is node 2, in a Sun Cluster 3.1 two node cluster from Solaris 10 Update 2, to 10 Update 7. This is a requirement for a NetApps solution as we currently have a Sun 3510 SAN. I am at a stage where I believe the two nodes will not communicate over the... (0 Replies)
Discussion started by: zetex
0 Replies

8. Solaris

Sun cluster 4.0 - zone cluster failover doubt

Hello experts - I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts. (1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over) (2) Or should i perform the installation on... (0 Replies)
Discussion started by: NVA
0 Replies

9. Solaris

Sun cluster v3.2 - Is this right?

Running Sun Cluster v3.2 it appears. Two clustered physcial servers both running Solaris 10. Both servers run a number of Oracle DBs etc. BUT I'm a bit concerned that its been set up but will never switch in the even of failure of one of the hosts? Some of the cluster groups we've... (3 Replies)
Discussion started by: psychocandy
3 Replies
CLUSTER(1)						      General Commands Manual							CLUSTER(1)

NAME
cluster - find clusters in a graph and augment the graph with this information. SYNOPSIS
cluster [-v?] [ -Ck ] [ -ck ] [ -o outfile ] [ files ] DESCRIPTION
cluster takes as input a graph in DOT format, finds node clusters and augments the graph with this information. The clusters are specified by the "cluster" attribute attached to nodes; cluster values are non-negative integers. cluster attempts to maximize the modularity of the clustering. If the edge attribute "weight" is defined, this will be used in computing the clustering. OPTIONS
The following options are supported: -Ck specifies a targeted number of clusters that should be generated. The specified number k is only a suggestion and may not be real- isable. If k == 0, the default, the number of clusters that approximately optimizes the modularity is returned. -ck specifies clustering method. If k == 0, the default, the modularity will be used. If k == 1 modularity quality will be used. -ooutfile Specifies that output should go into the file outfile. By default, stdout is used. -v Verbose mode. EXAMPLES
Applying cluster to the following graph, graph { 1--2 [weight=10.] 2--3 [weight=1] 3--4 [weight=10.] 4--5 [weight=10] 5--6 [weight=10] 3--6 [weight=0.1] 4--6 [weight=10.] } gives graph { node [cluster="-1"]; 1 [cluster=1]; 2 [cluster=1]; 3 [cluster=2]; 4 [cluster=2]; 5 [cluster=2]; 6 [cluster=2]; 1 -- 2 [weight="10."]; 2 -- 3 [weight=1]; 3 -- 4 [weight="10."]; 4 -- 5 [weight=10]; 5 -- 6 [weight=10]; 3 -- 6 [weight="0.1"]; 4 -- 6 [weight="10."]; } AUTHOR
Yifan Hu <yifanhu@research.att.com> SEE ALSO
gvmap(1) Blondel, V.D., Guillaume, J.L., Lambiotte, R., Lefebvre, E.: Fast unfolding of communities in large networks. Journal of Statistical Mechanics: Theory and Experiment (2008), P10008. 3 March 2011 CLUSTER(1)
All times are GMT -4. The time now is 03:41 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy