10-07-2011
i just want video how to install and configure sun cluster 3.1 or 3.2. For learning purpose.
9 More Discussions You Might Find Interesting
1. High Performance Computing
Dear All,
Can anyone explain about Pros and Cons of SUN and Veritas Cluster ?
Any comparison chart is highly appreciated.
Regards,
RAA (4 Replies)
Discussion started by: RAA
4 Replies
2. Solaris
hi
can u please send me how to configure cluster in x86 machines. i am using VM ware. Is there any difference in X86 and SPARC cluster installations
please help me
thaks to all (1 Reply)
Discussion started by: sijocg
1 Replies
3. Solaris
Hi,
I am getting these messages constantly at random times there is not visible impact but would like to know what these messages mean?
Cluster.RGM.rgmd: resource group
on node change to RG_ON_PENDING_R_RERT
Cluster.RGM.rgmd: resource group on node change to RG_ONLINE (1 Reply)
Discussion started by: xor
1 Replies
4. Solaris
Hi All
I hav working knowledge on solarois 10.
Could anyone suggest me any doc or material for learning SUN cluster from scratch. Anything from basic level .
Thanks in advance!! (1 Reply)
Discussion started by: ningy
1 Replies
5. Solaris
Yesterday my customer told me to expect a vcs upgrade to happen in the future. He also plans to stop using HDS and move to EMC.
Am thinking how to migrate to sun cluster setup instead.
My plan as follows leave the existing vcs intact as a fallback plan.
Then install and build suncluster on... (5 Replies)
Discussion started by: sparcguy
5 Replies
6. Solaris
Hi
I have a new mount point which is to added to to an existing resource group. I read many docs but I am not able to find the exact methods.
Could anyone help me pls. (1 Reply)
Discussion started by: ningy
1 Replies
7. Solaris
Hi,
I have upgraded a Sparc T2000 server which is node 2, in a Sun Cluster 3.1 two node cluster from Solaris 10 Update 2, to 10 Update 7. This is a requirement for a NetApps solution as we currently have a Sun 3510 SAN.
I am at a stage where I believe the two nodes will not communicate over the... (0 Replies)
Discussion started by: zetex
0 Replies
8. Solaris
Hello experts -
I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts.
(1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over)
(2) Or should i perform the installation on... (0 Replies)
Discussion started by: NVA
0 Replies
9. Solaris
Running Sun Cluster v3.2 it appears. Two clustered physcial servers both running Solaris 10.
Both servers run a number of Oracle DBs etc. BUT I'm a bit concerned that its been set up but will never switch in the even of failure of one of the hosts?
Some of the cluster groups we've... (3 Replies)
Discussion started by: psychocandy
3 Replies
LEARN ABOUT HPUX
cmrunnode
cmrunnode(1m) cmrunnode(1m)
NAME
cmrunnode - run a node in a high availability cluster
SYNOPSIS
cmrunnode [-v] [node_name...] [-t | -w none]
DESCRIPTION
cmrunnode causes a node to start its cluster daemon to join the existing cluster. This command verifies the network configuration before
causing the node to start its cluster daemon.
To start a cluster on one of its nodes, a user must either be superuser(UID=0), or have an access policy of FULL_ADMIN allowed in the clus-
ter configuration file. See access policy in cmquerycl(1m).
Starting a node will not cause any active packages to be moved to the new node. However, if a package is DOWN, has its switching enabled,
and is able to run on the new node, that package will automatically run there.
If node_name is not specified, the cluster daemon will be started on the local node and will join the existing cluster.
Options
cmrunnode supports the following options:
-v Verbose output will be displayed.
-t Test only. Provide an assessment of the package placement without affecting the current state of the nodes or packages. The -w
option is not required with the -t option as -t does not validate network connectivity, but assumes that all the nodes can meet
any external dependencies such as EMS resources, package subnets, and storage.
node_name...
Start the cluster daemon on the specified node(s).
-w none
By default network probing is performed to check that the network connectivity is the same as when the cluster was configured.
Any anomalies are reported before the cluster daemons are started. The -w none option disables this probing. The option should
only be used if this network configuration is known to be correct from a recent check.
RETURN VALUE
cmrunnode returns the following value:
0 Successful completion.
1 Command failed.
EXAMPLES
Run the cluster daemon on the current node:
cmrunnode
Run the cluster daemons on node1 and node2:
cmrunnode node1 node2
AUTHOR
cmrunnode was developed by HP.
SEE ALSO
cmquerycl(1m), cmhaltcl(1m), cmhaltnode(1m), cmruncl(1m), cmviewcl(1m), cmeval(1m).
Requires Optional Serviceguard Software cmrunnode(1m)