10-06-2011
thanx Hartz, sorry for late reply...
I've tried the
last | grep 192.xxxxx
but the result was nothing.
and ifconfig -a to look just for local IP, not all existing IP on my network? like 192.168.1.1; 192.168.1.2; 192.168.1.3.....etc
cmiiw
the problem is, I have a server that its name xxx.lan (example), and I usually access from Windows
start-run \ \ xxx, and now... forget what its IP
now, can i know the IP xxx, and anyone who access that server? and also the Log?
many thnx
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hey,
Just need a little help I'm not sure wat I should do.
We have several little networks setup for testing different things. One of these networks we need to have running at full dulpex.
Right now we run 2 hubs (to go off to 2 differnt parts) and they are half dulpex hubs.
Is is... (1 Reply)
Discussion started by: merlin
1 Replies
2. Linux
I have setup a AS 2.1 server with no X running or installed. I need to know how to configure the IP and such from command line and change it from DHCP. We used DHCP at first since we didn't know the IP we were going to use and now I need to change it. Any help would be great as Redhat's site just... (2 Replies)
Discussion started by: Acleoma
2 Replies
3. Solaris
I have a machine that has developed a strange network problem. Anytime it sends an FTP file somewherwe, no problem. When it is the target machine, extremely slow. I checked the /var/adm/messages file and found a few of these:
SUNW,hme0 : No response from Ethernet network : Link down -- cable... (2 Replies)
Discussion started by: hshapiro
2 Replies
4. UNIX for Dummies Questions & Answers
This is my first attempt in installing a netbsd ever. I'm trying to get myself familiar with some commands and how things work in unix and so far i never knew its this fun. Anyway, unix is our elective here in school and school is gonna start 2 weeks. I'm just trying to get a headstart on this :D... (2 Replies)
Discussion started by: 3rr0r_3rr0r
2 Replies
5. UNIX for Dummies Questions & Answers
1) how do i know my NIC speed if its 10//100???
2)how do i setup by NIC to full duplex
3) any help on setting up etherchannel for NIC failover (1 Reply)
Discussion started by: karthikosu
1 Replies
6. Solaris
I am new to Solaris and have been searching around for this answer and I think I figured it out but I wanted to run it by you folks. I was trying to figure out if the network on this Solaris 10 machine was set up for 100 Full Duplex. I think from this output that it is 100 full duplex, am I... (2 Replies)
Discussion started by: scotbuff
2 Replies
7. UNIX for Dummies Questions & Answers
Hi,
I have a linux machine connected to 2 networks, with devices eth0 and eth1.
When I give the command host whatever, how do I now which network is searched for the DNS's ? Is there a default ethernet device for network related commands ? How do I change it ? :confused: (2 Replies)
Discussion started by: mik
2 Replies
8. IP Networking
Hi here is my question;
any help would be appreciated
The Linux system pokey has two Ethernet cards. The first Ethernet card is connected to a companywide
TCP/IP network covering the addresses 87.65.43.xx, where pokey's address is
87.65.43.21. The second Ethernet interface is connected to a... (2 Replies)
Discussion started by: scofiled83
2 Replies
9. IP Networking
Folks;
I have 2 SUSE servers similar in all configuration & both on the same network
(192.168.151.10 & 192.168.151.11) with the same default gateway of 192.168.151.1 and the same netmask of 255.255.255.0 and the same firewall configuration
the first one works fine and i can ssh to it & i can... (3 Replies)
Discussion started by: Katkota
3 Replies
10. UNIX for Dummies Questions & Answers
Hi,
I am on Redhat 5. on the /etc/sysconfig/network file
I don't see GATEWAY as one line. I also checked /etc/sysconfig/network-scripts/ifcfg-eth0. I don't see GATEWAY.
But on the server. But when I do netstat -rn. I see many address. Is there some other settings ?
... (2 Replies)
Discussion started by: samnyc
2 Replies
LEARN ABOUT DEBIAN
nntp-pull
NNTP-PULL(1) nntp-pull manual NNTP-PULL(1)
NAME
nntp-pull - fetch articles from the server to the mbox
SYNOPSIS
nntp-pull [options...] groupname [groupname...]
DESCRIPTION
Fetch messages from the server and save them into the mailbox (mbox format). Every argument is supposed to be a name of group, optionally
followed by a '>' character and mbox filename. If the mbox filename is omitted, it defaults to the name of the group.
Besides global options (described in sinntp(1)), nntp-pull command takes following options:
--limit=N
Pull at most N messages.
--reget
Start from the first available message.
EXAMPLES
nntp-pull --server=news.example.org --limit=50 'comp.os.linux>os-linux' Fetches at most the 50 newest articles from the newsgroup
comp.os.linux located on news.example.org server and appends them to the os-linux mailbox file.
nntp-pull --server=news.example.net --reget --limit=3 comp.os.windows Fetches at most the 3 oldest articles from the newsgroup
comp.os.windows located on news.example.net server and appends them to the comp.os.windows mailbox file.
SEE ALSO
sinntp(1)
COPYRIGHT
Copyright (C) 2009, 2010, 2011 Piotr Lewandowski, Jakub Wilk
nntp-pull 1.5 2012-04-18 NNTP-PULL(1)