hi,
1) is logical partition the same as physical partition except that one is physical and the other is logical?
2) then it must a one to one ratio? (3 Replies)
I've created a partition with GNU Parted, how do I mount the partition?
The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards.
Thanks,
--Todd (1 Reply)
Hi all
i got this filesystem
Filesystem size used avail capacity Mounted on
/dev/dsk/c0t600A0B80001F350A000033404A5D29D9d0s2
492G 64M 487G 1% /u10
How do i change the name for /dev/dsk/c0t600A0B80001F350A000033404A5D29D9d0s2 to the... (3 Replies)
Gentleman,
Please move if I have chose the incorrect forum section. I am trying to move data that is not backed up from partition 1 to partition 2 on a SAN that has a GFS2 filesystem. Since the data is not backed up I am rsyncing this data and once verified I will delete from the source... (6 Replies)
Hi folks,
is there any possibility how to rename soft partitions??
Here I found that this is not possible (I know that it is) but I need do it in some supported way.
http://dlc.sun.com/osol/docs/content/LOGVOLMGRADMIN/tasks-basics-5.html
This is production system it is why I need do it... (0 Replies)
hi all
while formatting hard disk i am getting following error.
Partition 1 ends at 266338338
It must be between 34 and 143374704.
label error: EFI Labels do not support overlapping partitions
Partition 8 overlaps partition 1.
Warning: error writing EFI.
Label failed.
I have formatted the... (2 Replies)
Hi Experts
I would like to know different between soft partition concept and hard partition concept on solaris.
Here is little explanation between soft partition concept and hard partition concept on solaris.
Soft Partition:
1TB total space available in storage in all mapped to the OS to... (2 Replies)
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies
LEARN ABOUT MOJAVE
iptables-save
IPTABLES-SAVE(8) iptables 1.6.1 IPTABLES-SAVE(8)NAME
iptables-save -- dump iptables rules to stdout
ip6tables-save -- dump iptables rules to stdout
SYNOPSIS
iptables-save [-M modprobe] [-c] [-t table]
ip6tables-save [-M modprobe] [-c] [-t table]
DESCRIPTION
iptables-save and ip6tables-save are used to dump the contents of IP or IPv6 Table in easily parseable format to STDOUT. Use I/O-redirect-
ion provided by your shell to write to a file.
-M, --modprobe modprobe_program
Specify the path to the modprobe program. By default, iptables-save will inspect /proc/sys/kernel/modprobe to determine the exe-
cutable's path.
-c, --counters
include the current values of all packet and byte counters in the output
-t, --table tablename
restrict output to only one table. If not specified, output includes all available tables.
BUGS
None known as of iptables-1.2.1 release
AUTHORS
Harald Welte <laforge@gnumonks.org>
Rusty Russell <rusty@rustcorp.com.au>
Andras Kis-Szabo <kisza@sch.bme.hu> contributed ip6tables-save.
SEE ALSO iptables-apply(8),iptables-restore(8), iptables(8)
The iptables-HOWTO, which details more iptables usage, the NAT-HOWTO, which details NAT, and the netfilter-hacking-HOWTO which details the
internals.
iptables 1.6.1 IPTABLES-SAVE(8)