|
|
Sponsored Content
Top Forums
UNIX for Dummies Questions & Answers
Does formatting slice 2 (backup) destroy disk geometry?
Post 302561666 by fpmurphy on Tuesday 4th of October 2011 10:15:49 PM
10-04-2011
|
|
9 More Discussions You Might Find Interesting
1. Solaris
Hi there
I am about to mirror a Solaris 10 x86 box (SunFire X4100) onto a secondary disk using svm (current system is one disk). My question is this, on X86 boxes there is a slice 8 defined as boot partition (and also a slice 9, dunno what its used for tho). Do I need to mirror this boot slice... (0 Replies)
Discussion started by: hcclnoodles
0 Replies
2. UNIX for Advanced & Expert Users
How can one mirror disk geometry from one hard disk to another in Solaris.
Is disk snapshot same as a mirror? Pls explain. (3 Replies)
Discussion started by: lexusujx
3 Replies
3. Solaris
Not sure why solaris couldn't detect the geometry of a hard disk which has a working OS of winxp pro.
Is it due to the different OS that the partition information is stored in different location?
When I type '"format" it is shown as below,
c3d1 < drive type unknown>... (5 Replies)
Discussion started by: just.srad
5 Replies
4. Solaris
Hi,
Recently I faced with need of analyze root disk. I figured out two possible ways to do it:
1. Practical. Boot from CD and run format
2. Theoretical. Create live upgrade boot environment on another disk, activate it, reboot, unmont all root disk partitions and run format.
I've already... (3 Replies)
Discussion started by: Sapfeer
3 Replies
5. Shell Programming and Scripting
Hi Folks,
I am trying to make a script to assign all diskspace to slice 0, on multiple sized disks. Since the disks are new they may need to be labelled also to avoid the error: Cannot get disk geometry
Below is my code struggling with logic which doesn't seem to be producing the desired... (0 Replies)
Discussion started by: momin
0 Replies
6. Solaris
Hi there,
I am trying to do root volume mirroring on SunFire V210 server. I have two disks in it.First one is c1t0do and second one is c1t1do. Both disks already have partitions in them so I am deleting the partitions of second disk(c1t1do) using format command and selecting cylinder start 0... (2 Replies)
Discussion started by: newbi8321
2 Replies
7. Solaris
we have a ZFS file system that was created as a pool of just one disk (raid on a SAN) when this was created it was done as a whole disk, and so EFI label.
now we want to mount this file system into an LDOM.
my understanding of how ldom's and disk works this is that we can only do this as a... (1 Reply)
Discussion started by: robsonde
1 Replies
8. Solaris
Hi all,
I am using SPARC Solaris 11.1 with EFI labelled disks.
I am new to ZFS file systems and slightly stuck when trying to create a partition (slice) on one of my LUNs.
EFI labels use sectors and blocks and I am not sure how exactly it works.
From here I can try and create a... (2 Replies)
Discussion started by: selectstar
2 Replies
9. Solaris
Hi,
How to to make a slice and define as ufs from zpool? Please advice me.
Thanks.
---------- Post updated at 01:53 AM ---------- Previous update was at 12:24 AM ----------
Before slice:
Part Tag Flag Cylinders Size Blocks
0 root wm 0 ... (2 Replies)
Discussion started by: mzainal
2 Replies
LEARN ABOUT OPENSOLARIS
addbadsec
addbadsec(1M) System Administration Commands addbadsec(1M) NAME
addbadsec - map out defective disk blocks SYNOPSIS
addbadsec [-p] [-a blkno [blkno]...] [-f filename] raw_device DESCRIPTION
addbadsec is used by the system administrator to map out bad disk blocks. Normally, these blocks are identified during surface analysis, but occasionally the disk subsystem reports unrecoverable data errors indicating a bad block. A block number reported in this way can be fed directly into addbadsec, and the block will be remapped. addbadsec will first attempt hardware remapping. This is supported on SCSI drives and takes place at the disk hardware level. If the target is an IDE drive, then software remapping is used. In order for software remapping to succeed, the partition must contain an alternate slice and there must be room in this slice to perform the mapping. It should be understood that bad blocks lead to data loss. Remapping a defective block does not repair a damaged file. If a bad block occurs to a disk-resident file system structure such as a superblock, the entire slice might have to be recovered from a backup. OPTIONS
The following options are supported: -a Adds the specified blocks to the hardware or software map. If more than one block number is specified, the entire list should be quoted and block numbers should be separated by white space. -f Adds the specified blocks to the hardware or software map. The bad blocks are listed, one per line, in the specified file. -p Causes addbadsec to print the current software map. The output shows the defective block and the assigned alternate. This option can- not be used to print the hardware map. OPERANDS
The following operand is supported: raw_device The address of the disk drive (see FILES). FILES
The raw device should be /dev/rdsk/c?[t?]d?p0. See disks(1M) for an explanation of SCSI and IDE device naming conventions. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Architecture |x86 | +-----------------------------+-----------------------------+ |Availability |SUNWcsu | +-----------------------------+-----------------------------+ SEE ALSO
disks(1M), diskscan(1M), fdisk(1M), fmthard(1M), format(1M), attributes(5) NOTES
The format(1M) utility is available to format, label, analyze, and repair SCSI disks. This utility is included with the addbadsec, diskscan(1M), fdisk(1M), and fmthard(1M) commands available for x86. To format an IDE disk, use the DOS "format" utility; however, to label, analyze, or repair IDE disks on x86 systems, use the Solaris format(1M) utility. SunOS 5.11 24 Feb 1998 addbadsec(1M)