09-29-2011
This depends entirely on the type of system and type of disk you are adding.
Is it an internal disk?
Is it scsi / sas?
Is it a SAN disk.
Without a lot more information we cannot help you.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
hi friends,
one of my clnts wants his Hard drive to be ugrded . He is currently using SCO unix 5.04 on a 4.3 Gig SCSI drive. He wants me to upgrd it to 18 Gigs . All he wants is that the data / programs / userfiles shall be intact. he has 3 user slices /user1, /user2 , /user3 presently... (3 Replies)
Discussion started by: /etc/passwd
3 Replies
2. AIX
I have some problem to add a fujitsu Model MAT3147NC on my Aix 5.1 Server. When i run the cfgmrg command and after de lspv command, i can see my disk but i think it's missing some drivers to get operational.
Thank's for your help. (0 Replies)
Discussion started by: sdulude01
0 Replies
3. UNIX for Dummies Questions & Answers
Hello Everybody,
I have sun machine running Sol9 with ntpq running on it, and I have a network time server, I want to synchronize my sun machine with that time server, is there any way I can add the time server to my sun machine,
root@yuda> ntpq
ntpq> peers
localhost: timed out, nothing... (4 Replies)
Discussion started by: aladdin
4 Replies
4. SCO
please help me
i have two same server sco 5.0.6 and, one server os now not working
so i want to add same harddisk to my another same server ,after that i
can take backup it is so important please .
pankaj raval (6 Replies)
Discussion started by: pankajbraval
6 Replies
5. Solaris
Hi,
Please tell me the procedure to take root backup of a Solaris server. (6 Replies)
Discussion started by: Renjesh
6 Replies
6. Filesystems, Disks and Memory
Hi,
I have a server that I am adding a RAID that we purchased to. The server works fine. It is running Fedora 7 and is a Dell Precision 690.
When the RAID is attached, it boots up and says the following:
Controller Bus #00, Device#1F, Function#02: 00 Ports
No device found
AHCI BIOS not... (0 Replies)
Discussion started by: user23
0 Replies
7. Solaris
Hello Everybody
I would like to know that I have configure the OS & other application on the SunFire V440 server
1) If suppose no hostid base software install in that v440 server & if some problem comes in the motherboard of that server. If I remove the harddisk ( on which Solaris & other... (4 Replies)
Discussion started by: girish.batra
4 Replies
8. Windows & DOS: Issues & Discussions
Hi All,
I need your expertise in finding a way to solve my problem.Please excuse if this is not the right forum to ask this question and guide me to the correct forum,if possible.
I am a DBA and on a daily basis i have to ftp huge dump files from my company server to my laptop and then... (3 Replies)
Discussion started by: kunwar
3 Replies
9. Programming
Hello!
I searched forum for similar topic, with no luck, if you know one, delete this topic, and send me private message with link please.
Little background:
I have a lot of clients and one serwer. Client can make multiple connections on different ports and ips, but only one can be acctive... (2 Replies)
Discussion started by: ikeban
2 Replies
10. Solaris
Hi all,
As per the topic goes,
q1) how do i check remotely (over ssh) - how many physical network interfaces I really have ? -- if an interface exists before and it got plug out, it must not be show again.
-- i tried dladm show-link and ifconfig -a, but it seems to show a previously... (4 Replies)
Discussion started by: javanoob
4 Replies
LEARN ABOUT X11R4
perlivp
PERLIVP(1) Perl Programmers Reference Guide PERLIVP(1)
NAME
perlivp - Perl Installation Verification Procedure
SYNOPSIS
perlivp [-a] [-p] [-v] [-h]
DESCRIPTION
The perlivp program is set up at Perl source code build time to test the Perl version it was built under. It can be used after running:
make install
(or your platform's equivalent procedure) to verify that perl and its libraries have been installed correctly. A correct installation is
verified by output that looks like:
ok 1
ok 2
etc.
OPTIONS
-h help
Prints out a brief help message.
-a run all tests
Normally tests for optional features are skipped. With -a all tests are executed.
-p print preface
Gives a description of each test prior to performing it.
-v verbose
Gives more detailed information about each test, after it has been performed. Note that any failed tests ought to print out some
extra information whether or not -v is thrown.
DIAGNOSTICS
* print "# Perl binary `$perlpath' does not appear executable.
";
Likely to occur for a perl binary that was not properly installed. Correct by conducting a proper installation.
* print "# Perl version `$]' installed, expected $ivp_VERSION.
";
Likely to occur for a perl that was not properly installed. Correct by conducting a proper installation.
* print "# Perl @INC directory `$_' does not appear to exist.
";
Likely to occur for a perl library tree that was not properly installed. Correct by conducting a proper installation.
* print "# Needed module `$_' does not appear to be properly installed.
";
One of the two modules that is used by perlivp was not present in the installation. This is a serious error since it adversely affects
perlivp's ability to function. You may be able to correct this by performing a proper perl installation.
* print "# Required module `$_' does not appear to be properly installed.
";
An attempt to "eval "require $module"" failed, even though the list of extensions indicated that it should succeed. Correct by con-
ducting a proper installation.
* print "# Unnecessary module `bLuRfle' appears to be installed.
";
This test not coming out ok could indicate that you have in fact installed a bLuRfle.pm module or that the "eval " require "$mod-
ule_name.pm"; "" test may give misleading results with your installation of perl. If yours is the latter case then please let the
author know.
* print "# file",+($#missing == 0) ? '' : 's'," missing from installation:
";
One or more files turned up missing according to a run of "ExtUtils::Installed -> validate()" over your installation. Correct by con-
ducting a proper installation.
* print "# Perl header `$_' does not appear to be properly installed.
";
Correct by running h2ph over your system's C header files. If necessary, edit the resulting *.ph files to eliminate perl syntax
errors.
For further information on how to conduct a proper installation consult the INSTALL file that comes with the perl source and the README
file for your platform.
AUTHOR
Peter Prymmer
perl v5.8.9 2009-04-13 PERLIVP(1)