The log filled with error messages about how it was too tiny, but it still mounted, contained valid-looking files, and let me edit. The size wasn't off by a factor of a thousand this time so this at least stands a better chance of working than my last try. Good luck to you.
I need to install a raid HBA internal card on a T5240. The reason is I have
more drives and the current mother board controller does not support more
than 4 drives.
My question is I have raidctl set up on current drives. If I install new HBA
card do I have to delete current raidctl and... (3 Replies)
Hi,
I need to redirect internal internet requests to a auth client site siting on the gateway. Currently users that are authenticated to access the internet have there mac address listed in the FORWARD chain. All other users need to be redirected to a internal site for authentication.
Can... (1 Reply)
Hi all
i would like to ask some suggests about my next job!
I have to install a new Sun Netra T5220, with an additional internal StorageTek SAS HBA Raid.
The problem come in if every disk is now controlled by the HBA, how can I install the OS?
No disk is being detected by the OS.
SAS card... (2 Replies)
I have a V490 that has couple internal disks attached to the same dual-port HBA card that I'm planning attach to the SAN for additional storage.
Would I sacrifice performance if I use the same HBA?
Is it better to throw in a new HBA instead? (1 Reply)
I need some assistance formatting a compact flash card in Ubtunu.
I connect up the CF card through a USB reader. Ubuntu recognizes the reader usb device, but does not "mount" the CF card as a device.
The CF card was formatted in FAT32 format.
Any help would be greatly appreciated.... (3 Replies)
Around a month ago we suffered a prolonged power outage, due to circumstances the servers and storage arrays were still in use when the UPS dropped. One of the servers was running a flash copy on the database while batch processing had commenced. This is the only server that suffered any further... (2 Replies)
Hi All,
I have a rather stange set of requirements that I'm hoping someone here could help me with. We receive a file that is actually a concatenation of 4 files (don't believe this would change, but ideally the solution would handle n files).
The super-file looks like:... (7 Replies)
I have noticed that when I copy files to flash disk and in UI I see message copy completed in notification area on task bar, usually copy is not completed. So, if I eject the media I loose data.
It is very serious problem because may cause loss of valuable and even critical data.
Moreover, when... (2 Replies)
Hi
I have been trying to figure a way to copy a file, (a template), that has internal variables. Using the values as defined for those variables in another script.
So a file called x -
#! /bin/bash
D=aa.$X.bb
And file y
#! /bin/bash
X=6
while read line
do
eval echo... (5 Replies)
Hey guys, wondering if this is possible to accomplish.
PowerHA SystemMirror7.1 active/passive cluster. Restored a clustered system in test and upgraded to the latest version of PowerHA. Things are working great. However in the interest of time during cut over to the new system, I was hoping to... (4 Replies)
Discussion started by: j_aix
4 Replies
LEARN ABOUT OPENSOLARIS
xfs_info
xfs_growfs(8) System Manager's Manual xfs_growfs(8)NAME
xfs_growfs, xfs_info - expand an XFS filesystem
SYNOPSIS
xfs_growfs [ -dilnrxV ] [ -D size ] [ -e rtextsize ] [ -L size ] [ -m maxpct ] [ -t mtab ] [ -R size ] mount-point
xfs_info [ -t mtab ] mount-point
DESCRIPTION
xfs_growfs expands an existing XFS filesystem (see xfs(5)). The mount-point argument is the pathname of the directory where the filesystem
is mounted. The filesystem must be mounted to be grown (see mount(8)). The existing contents of the filesystem are undisturbed, and the
added space becomes available for additional file storage.
xfs_info is equivalent to invoking xfs_growfs with the -n option (see discussion below).
OPTIONS -d | -D size
Specifies that the data section of the filesystem should be grown. If the -D size option is given, the data section is grown to that
size, otherwise the data section is grown to the largest size possible with the -d option. The size is expressed in filesystem
blocks.
-e Allows the real-time extent size to be specified. In mkfs.xfs(8) this is specified with -r extsize=nnnn.
-i The new log is an internal log (inside the data section). [NOTE: This option is not implemented]
-l | -L size
Specifies that the log section of the filesystem should be grown, shrunk, or moved. If the -L size option is given, the log section
is changed to be that size, if possible. The size is expressed in filesystem blocks. The size of an internal log must be smaller
than the size of an allocation group (this value is printed at mkfs(8) time). If neither -i nor -x is given with -l, the log contin-
ues to be internal or external as it was before. [NOTE: These options are not implemented]
-m Specify a new value for the maximum percentage of space in the filesystem that can be allocated as inodes. In mkfs.xfs(8) this is
specified with -i maxpct=nn.
-n Specifies that no change to the filesystem is to be made. The filesystem geometry is printed, and argument checking is performed,
but no growth occurs.
-r | -R size
Specifies that the real-time section of the filesystem should be grown. If the -R size option is given, the real-time section is
grown to that size, otherwise the real-time section is grown to the largest size possible with the -r option. The size is expressed
in filesystem blocks. The filesystem does not need to have contained a real-time section before the xfs_growfs operation.
-t Specifies an alternate mount table file (default is /proc/mounts if it exists, else /etc/mtab). This is used when working with
filesystems mounted without writing to /etc/mtab file - refer to mount(8) for further details.
-V Prints the version number and exits. The mount-point argument is not required with -V.
xfs_growfs is most often used in conjunction with logical volumes (see md(4) and lvm(8) on Linux). However, it can also be used on a regu-
lar disk partition, for example if a partition has been enlarged while retaining the same starting block.
PRACTICAL USE
Filesystems normally occupy all of the space on the device where they reside. In order to grow a filesystem, it is necessary to provide
added space for it to occupy. Therefore there must be at least one spare new disk partition available. Adding the space is often done
through the use of a logical volume manager.
SEE ALSO mkfs.xfs(8), md(4), lvm(8), mount(8).
xfs_growfs(8)