Cross-compiling libiconv for uclinux Post: 302559861

4 More Discussions You Might Find Interesting

1. Programming

Cross compiling under Windows for Linux

I have two headless servers I am writing code for, and a Windows box networked with them. I want to compile my code within an IDE on the Windows box (eclipse most likely) and run the compiled binarys on the Linux boxes. Will this work? Using Cygwin (or MinGW)? Thoughts? Cheers, Ian

2. Linux

Help Cross compiling a kernel for an HP Jornada 728

Hello, I just bought an old Jornada 728 and, as you may know, it comes with Windows CE 3.0. I do not use Windows, so i wanted to create my own linux system for the Jornada. I know there are projects like Jlime, Familiar Linux, 720 Degrees, etc. But i want something based on the distribution i...

3. Solaris

Which version of "libiconv" is libiconv.so.2 in?

Hi All, I am getting this in a compile error: >gcc 1.c ld.so.1: gcc: fatal: libiconv.so.2: open failed: No such file or directory Killed I know this lib is in libiconv, but NONE of the below ones have that particular version in it: Does anyonw know exatly where it is at? maybe 1.7? 1.6?...

4. UNIX and Linux Applications

Cross Compiling Issue of udev-151 for MIPS Little Endain Architecture

Hi All, I am trying to cross compile udev-151 for MIPS little endian architecture. I am configuring like this: ./configure --prefix=$PWD/sree --host=mips-linux-gnu configure: WARNING: If you wanted to set the --build type, don't use --host. If a cross compiler is detected then...

LEARN ABOUT XFREE86

dh_auto_install

DH_AUTO_INSTALL(1)						     Debhelper							DH_AUTO_INSTALL(1)

NAME
       dh_auto_install - automatically runs make install or similar

SYNOPSIS
       dh_auto_install [buildsystemoptions] [debhelperoptions] [--params]

DESCRIPTION
       dh_auto_install is a debhelper program that tries to automatically install built files. It does so by running the appropriate command for
       the build system it detects the package uses. For example, if there's a Makefile and it contains a install target, then this is done by
       running make (or MAKE, if the environment variable is set). If there is a setup.py or Build.PL, it is used. Note that the Ant build system
       does not support installation, so dh_auto_install will not install files built using Ant.

       Unless --destdir option is specified, the files are installed into debian/package/ if there is only one binary package. In the multiple
       binary package case, the files are instead installed into debian/tmp/, and should be moved from there to the appropriate package build
       directory using dh_install(1).

       DESTDIR is used to tell make where to install the files.  If the Makefile was generated by MakeMaker from a Makefile.PL, it will
       automatically set PREFIX=/usr too, since such Makefiles need that.

       This is intended to work for about 90% of packages. If it doesn't work, or tries to use the wrong install target, you're encouraged to skip
       using dh_auto_install at all, and just run make install manually.

OPTIONS
       See "BUILD SYSTEM OPTIONS" in debhelper(7) for a list of common build system selection and control options.

       --destdir=directory
	   Install files into the specified directory. If this option is not specified, destination directory is determined automatically as
	   described in the "DESCRIPTION" section.

       -- params
	   Pass params to the program that is run, after the parameters that dh_auto_install usually passes.

SEE ALSO
       debhelper(7)

       This program is a part of debhelper.

AUTHOR
       Joey Hess <joeyh@debian.org>

11.1.6ubuntu2							    2018-05-10							DH_AUTO_INSTALL(1)