I use DHCP on my AIX box at home . I want to connect to my Cable ISP as a
DHCP Client . the thing I did was this :
smit
Communications Applications and Services
TCP/IP
Use DHCP for TCPIP Configuration and Startup
"Select the interface you want to use"
en0
"Enter a hostname"
OK
after... (3 Replies)
Hi,
We had an upgrade today morning and since then mailx command is not working.
I have been told to change the DNS to use host name as smtp.companyname.com instead of the IP address.
Can someone please help me out to know where can I change this on a Unix Server.
Thanks
Aman (5 Replies)
I am pretty new to this. My router was earlier configured to enable DHCP, thus my UNIX box is using the dhcp address, i.e. I have to do a ifconfig dhcp hme0 start. Since I am planning to use my NT as a web server, I needed to use the static IP address. How do I configure the unix box to use the... (5 Replies)
Hi All,
i have been accessing ip address through DHCP for my windows..i tried to configure the same for solaris also and got the error " Failed to configure IPv4 for DHCP afe0 "
can anyone explain what should i do ...i want to acees internet in solaris
am i need to configure for... (0 Replies)
We have configured our mail unix server and can send out emails automatically from applications running on unix to different people in our company as well as outside our company. However there is an outside client who is not receiving these emails because the settings on their mail server cannot... (4 Replies)
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
I try a static ip assign mode while i installed the Solaris 10(U 8). But i can't access the internet, i try the ifconfig -a command and see my configuration is correct in the interface. So i want to get my ip using dhcp. I search from internet. They give me the suggestions.
ifconfig interface... (1 Reply)
I have a question. How to write the DHCP to assign the default-gateway to clients.
Thank you. (2 Replies)
Discussion started by: thsecmaniac
2 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)