09-18-2011
This User Gave Thanks to mark54g For This Post:
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have installed in the server a quad ethernet adapter, I'm using two interfaces with two different IP networks, both interfaces are connected to a switch, the switch report that is receiving the same MAC address in both ports so must of the times I have connectivity problems.
Any idea to change... (1 Reply)
Discussion started by: mono673
1 Replies
2. Solaris
I have a Dual Boot system - XP with Solaris 10. I built the system from the ground up with different components and the Ethernet Card built into the Motherboard is a Marvell Yukon Gigabit Ethernet 10/100/1000 T-base, RJ-45 Copper.
I am unable to go to the Web as the Ethernet Card is still not... (2 Replies)
Discussion started by: tubbyrana
2 Replies
3. Solaris
hi all,
How to install onboard ethernet card on Sun SPARC M4000 server? (3 Replies)
Discussion started by: Tlg13team
3 Replies
4. AIX
Hi,
In our AIX 5.2 server , we have one unused ethernet adapter which doesn't have cable connection . For this interface , we are getting alerts in errpt .
Could you suggesthow to stop this alert ? And sametime i would like to keep this device in ODM .
Is there... (1 Reply)
Discussion started by: sekarsamy
1 Replies
5. AIX
All
I am trying allocate an IVE to an LPAR (not a VIO) running AIX 7.1. I am getting the error:
HSCL068A
Explanation
Logical port can not be assigned to Logical Partition because this Logical Partition is not the promiscuous LPAR for the physical port.
Has anyone encountered this... (1 Reply)
Discussion started by: johnf
1 Replies
6. Hardware
Hi,
Does anybody have a "Sun 10-Gigabit Ethernet Adapter installation CD" or driver ixge for Sun 10-Gigabit Ethernet PCI-X adapter? I need it but can't find it anywhere. So if you know where I can download it or purchase it, please let me know. (Already tried Oracle's website, don't have it) ... (5 Replies)
Discussion started by: Lhao
5 Replies
7. AIX
Hi Techies,
I have a doubt.
ent0 Available Logical Host Ethernet Port (lp-hea)
ent1 Available Logical Host Ethernet Port (lp-hea)
ent2 Available Logical Host Ethernet Port (lp-hea)
ent3 Available Logical Host Ethernet Port (lp-hea)
ent4 Available... (4 Replies)
Discussion started by: jayadeava
4 Replies
8. Solaris
Hi Community,
i have one issue with 10 fiber ethernet adapter.
here is my details:
root@new-bpel.example.com #dladm show-dev
bge0 link: unknown speed: 0 Mbps duplex: unknown
bge1 link: up speed: 1000 Mbps duplex: full
qlge2 link:... (4 Replies)
Discussion started by: bentech4u
4 Replies
9. Red Hat
Hello community, I have a Proliant HP DL380P with the following network adapters:
NetXtreme BCM5719 Gigabit Ethernet PCIe (Ethernet 1Gb 4-port 331FLR Adapter)
82580 Gigabit Network Connection (NC365T 4-port Ethernet Server Adapter)
I installed Red Hat 7.2 but it recognizes only the... (9 Replies)
Discussion started by: Lord Spectre
9 Replies
10. AIX
Hi,
We had a hardware problem with an IBM System p5 server, with AIX 5.2
We restore from a tape the last backup we had, but the server does not boot up as expected.
The server try to mount some directories from a storage, but could not comunicate with them, we check the FC and everything is... (12 Replies)
Discussion started by: trevian3969
12 Replies
EX(4) BSD/i386 Kernel Interfaces Manual EX(4)
NAME
ex -- Ethernet device driver for the Intel EtherExpress Pro/10 and Pro/10+
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device ex
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_ex_load="YES"
DESCRIPTION
The ex driver provides support for Ethernet adapters based on the Intel i82595 chip.
On the ISA bus, the card will be searched for in the I/O address range 0x200 - 0x3a0. The IRQ will be read from the EEPROM on the card. For
correct operation Plug-N-Play support should be disabled.
On the PC Card bus, the card will be automatically recognized and configured.
HARDWARE
The ex driver supports the following Ethernet adapters:
o Intel EtherExpress Pro/10 ISA
o Intel EtherExpress Pro/10+ ISA
o Olicom OC2220 Ethernet PC Card
o Olicom OC2232 Ethernet/Modem PC Card
o Silicom Ethernet LAN PC Card
o Silicom EtherSerial LAN PC Card
DIAGNOSTICS
ex%d: Intel EtherExpress Pro/10, address %6D, connector %s The device probe found an installed card, and was able to correctly install the
device driver.
ex%d: WARNING: board's EEPROM is configured for IRQ %d, using %d The device probe detected that the board is configured for a different
interrupt than the one specified in the kernel configuration file.
ex%d: invalid IRQ. The device probe detected an invalid IRQ setting.
SEE ALSO
arp(4), netintro(4), ng_ether(4), ifconfig(8)
HISTORY
The ex device driver first appeared in FreeBSD 2.2.
AUTHORS
The ex device driver was written by Javier Martin Rueda. The PC Card attachment was written by Mitsuru ISAWAKI and Warner Losh. This manual
page was written by David E. O'Brien.
BUGS
Currently the driver does not support multicast.
The Silicom EtherSerial card's serial port does not currently work. The Olicom OC2232 PC Card should work with the ex driver, but is cur-
rently completely broken.
BSD
July 16, 2005 BSD